Hello Odhiambo . The 3G model is Huawei E173 with Movistar Argentina.
Ive tried but i cant see in windows de USB port to have a serial link :( Saludos / Regards Leonardo Santagostini 2013/3/27 Odhiambo Washington <[email protected]> > > On 27 March 2013 16:29, Leonardo Santagostini <[email protected]>wrote: > >> Hello all. >> >> I have a latitude e6400 with FreeBSD Release 9.1. And i can't get the USB >> modem working. >> >> I tried with umodem, u3g but no luck :( >> > > [snip] > > >> ugen7.2: <HUAWEI> at usbus7 >> ugen7.2: <HUAWEI> at usbus7 (disconnected) >> ugen7.2: <HUAWEI> at usbus7 >> umodem0: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on >> usbus7 >> umodem0: data interface 0, has no CM over data, has no break >> umodem1: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on >> usbus7 >> umodem1: data interface 1, has no CM over data, has no break >> umodem2: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on >> usbus7 >> umodem2: data interface 2, has no CM over data, has no break >> umass0: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7 >> umass0: SCSI over Bulk-Only; quirks = 0x0000 >> umass0:9:0:-1: Attached to scbus9 >> cd1 at umass-sim0 bus 0 scbus9 target 0 lun 0 >> cd1: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device >> cd1: 40.000MB/s transfers >> cd1: Attempt to query device size failed: NOT READY, Medium not present >> umass1: <HUAWEI HUAWEI Mobile, class 0/0, rev 2.00/1.02, addr 2> on usbus7 >> umass1: SCSI over Bulk-Only; quirks = 0x0000 >> umass1:10:1:-1: Attached to scbus10 >> da0 at umass-sim1 bus 1 scbus10 target 0 lun 0 >> da0: <HUAWEI SD Storage 2.31> Removable Direct Access SCSI-2 device >> da0: 40.000MB/s transfers >> da0: Attempt to query device size failed: NOT READY, Medium not present >> > > > [snip] > > Huawei modem, as I can see. That should be easy. > > Connect to the modem through HyperTerminal or Putty on a different machine > Issue the command: AT^U2DIAG=0 > That should disable the virtual CD-ROM and FreeBSD will see the modem. > > Here are some commands you'll need to know about: > Do you have a Windows PC near you? If you plug the device into it and the > virtualCD pops up, then it means command was not successful. The fact that > fake CD still shows means command did not succeed! > > AT^u2diag=0 (all off) > AT^u2diag=1 (CD on, SD off) > AT^u2diag=256 (CD off, SD is on) > AT^u2diag=255 (all on - including SD Card) > AT^u2diag=276 (Factory Reset) > A+CLAC - Display all available commands. However it does not tell you how > to use them > > > > And here is a working ppp.conf - but you need to change the *bolded* values > to match your end of the environment:) > > u3g: > set device */dev/cuaU0.0* > set server /var/run/3g-internet "" 0177 > set speed 921600 > set timeout 0 > set authname *saf* > set authkey *data* > set dial "ABORT BUSY ABORT NO\\sTIMEOUT 2 \ > \"\" \ > AT OK-AT-OK \ > AT+CFUN=1 OK-AT-OK \ > AT+CMEE=2 OK-AT-OK \ > AT+CSQ OK \ > AT+CGDCONT=1,\\\"IP\\\",\\\"*APN*\\\" OK \ > ATD**99#* CONNECT" > set crtscts on > disable vjcomp > disable acfcomp > disable deflate > disable deflate24 > disable pred1 > disable protocomp > disable mppe > disable ipv6cp > disable lqr > disable echo > #nat enable yes > enable dns > resolv writable > set dns 8.8.8.8 > set ifaddr 10.1.0.2/0 10.1.0.1/0 255.255.255.255 0.0.0.0 > add default HISADDR # See ppp.link* > > > Lemme know if you get stuck. > > Also, always give details about modem - manufacturer, model... > > > -- > Best regards, > Odhiambo WASHINGTON, > Nairobi,KE > +254733744121/+254722743223 > "I can't hear you -- I'm using the scrambler." > _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[email protected]"
