Hi, i already posted this on x11 but hey i really need help so please don't hold it against me...
I have an acer aspire 1350LC with a via chipset for the graphics. I got x working once on 4.9, same laptop when i had been messing around with 4.4.0 and ports so after a while it was a really broken install but suddenly it started working using the auto configure thing, first thing i tried to do was to write my own conf file which failed over and over again. I can't use the auto configure thing since it produced a very low resolution, even if i could figure out how to use auto configure with xfree and increase the res i doubt i'd be able to reproduce last time on 5.2.1 now because it was all a large mess of ports and bloody xfree86 guts all over the place. Anyways the situation now is that i get no errors to stdout. Checking the logfile i see that everything is going just fine until it reads the hsync value, this is what it looks like: (--) via(0): No DDC signal (II) via(0): Monitor0: Using hsync value of 31.50 kHz (II) via(0): Monitor0: Using vrefresh range of 50.00-90.00 Hz (II) via(0): Clock range: 20.00 to 230.00 MHz (II) via(0): Not using default mode "640x350" (hsync out of range) (II) via(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "640x400" (hsync out of range) (II) via(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "720x400" (hsync out of range) (II) via(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "640x480" (hsync out of range) (II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "640x480" (hsync out of range) (II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "640x480" (hsync out of range) (II) via(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) [...] (II) via(0): Not using default mode "1600x1024" (hsync out of range) (II) via(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) via(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) via(0): Not using mode "1024x768" (no mode of this name) (--) via(0): Virtual size is 640x480 (pitch 640) (**) via(0): *Default mode "640x480": 25.2 MHz (scaled from -1206751.2 MHz), 31.5 kHz, 60.0 Hz (II) via(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync After this it goes on with loading a few modules, showing me some resource ranges after preInit, mapping frambuffer and exits after a few of these messages. (II) via(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (==) via(0): Write-combining range (0xa0000,0x10000) was already clear Med vänliga hälsningar Stefan Midjich, Swebase AB Tel: 042-20 15 00 Fax: 042-20 15 03 E-post: [EMAIL PROTECTED] Webb: http://swebase.com _______________________________________________ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
