On Saturday 30 January 2010 11:04:15 am Alexander Motin wrote: > Steven Friedrich wrote: > > I stopped the boot before the timer expired, after it had loaded modules > > specified in /boot/loader.conf > > > > I loaded mmc, mmcsd, and sdhci. > > > > I continued the boot, and it panic'ed right after apic. > > > > I rebooted everal times, to load each individually, to narrow it down to > > sdhci. > > > > Can anyone verify that sdhci is compatible with FreeBSD 8? > > > > I updated and built today. > > I am using it daily since written it and till present 9-CURRENT. Show > your verbose boot messages and crash information. > I updated source and built world and kernel today. My machine won't complete a dump and reboot. I'll work on that, but the below text is from a successful boot, and I show where the panic occurred. I don't build all modules, but I added mmc, mmcsd, and sdhci to the var in make.conf. When this all began, I had built the modules and loaded them by hand. There was no panic, so I added them to /boot/loader.conf and then it panic'ed. I've also made it panic by stopping the boot and hand-loading the three modules. I haven't built these into a kernel...
Copyright (c) 1992-2010 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-STABLE #31: Sat Jan 30 16:19:51 EST 2010 ad...@laptop2.stevenfriedrich.org:/usr/obj/usr/src/sys/LAPTOP i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2793.02-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf41 Stepping = 1 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x641d<SSE3,DTES64,MON,DS_CPL,CNXT-ID,CX16,xTPR> AMD Features=0x20100000<NX,LM> TSC: P-state invariant real memory = 2147483648 (2048 MB) avail memory = 2094256128 (1997 MB) ACPI APIC Table: <HP 3082 > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads cpu0 (BSP): APIC ID: 0 cpu1 (AP/HT): APIC ID: 1 ioapic0 <Version 2.0> irqs 0-23 on motherboard Here, it reported a trap 12 page fault while in Kernel mode fault code supervisor read, page not present The next line would have been: video4bsd: /dev/video0..9, /dev/video_daemon0..9 Here's a snip from the original topic and a response: On Friday 29 January 2010 23:14:06 Steven Friedrich wrote: > I'd like to access the digital media slots on my laptop. > > Specifically, I want to read Sony Memory Sticks. > > pciconf -lv shows the devices: > > no...@pci0:11:0:3: class=0x018000 card=0x3082103c chip=0x8033104c rev=0x00 > hdr=0x00 > vendor = 'Texas Instruments (TI)' > device = 'PCIxx11/21 Integrated FlashMedia Controller' > class = mass storage > no...@pci0:11:0:4: class=0x080500 card=0x3082103c chip=0x8034104c rev=0x00 > hdr=0x00 > vendor = 'Texas Instruments (TI)' > device = 'SDA Standard Compliant SD Host Controller (10981734)' > class = base peripheral > subclass = SD host controller Probably supported by sdhci(4). I don't know which of the two controllers supports Sony Memory Sticks, but I figured I'd get the drivers installed and try it. _______________________________________________ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"