On Tue, 3 May 2011, Dmitry Morozovsky wrote: DM> DM> Well, I tried, and unfortunately I can not say that I'm happy after the DM> DM> upgrade. :( DM> DM> DM> DM> Particularly, adapter now takes *VERY* long time (>10 minutes) to initialize, DM> DM> and report as "ERROR" in BIOS utility (while seeing all 24 disks; however, it DM> DM> reports 8 x36 expanders instead of one). DM> DM> DM> DM> I can't boot the system off this array yet; will experiment further :( DM> DM> booted from USB stick, I have constantly repeating DM> DM> (ses3:mps0:0:25:0): lost device DM> (ses3:mps0:0:25:0): removing device entry DM> ses3 at mps0 bus 0 scbus0 target 25 lun 0 DM> ses3: <LSI CORP SAS2X36 0417> Fixed Enclosure Services SCSI-5 device DM> ses3: 600.000MB/s transfers DM> ses3: Command Queueing enabled DM> ses3: SCSI-3 SES Device DM> DM> for different sesN, which are detected many times: DM> DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 0 lun 0 (da0,pass0) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 1 lun 0 (da1,pass1) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 2 lun 0 (da2,pass2) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 3 lun 0 (pass11,da4) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 4 lun 0 (pass12,da5) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 5 lun 0 (pass9,da3) DM> <LSI CORP SAS2X36 0417> at scbus0 target 24 lun 0 (pass5,ses3) DM> <LSI CORP SAS2X36 0417> at scbus0 target 25 lun 0 (pass19,ses5) DM> <LSI CORP SAS2X36 0417> at scbus0 target 26 lun 0 (pass10,ses4) DM> <LSI CORP SAS2X36 0417> at scbus0 target 27 lun 0 (pass14,ses7) DM> <LSI CORP SAS2X36 0417> at scbus0 target 33 lun 0 (pass13,ses6) DM> <LSI CORP SAS2X36 0417> at scbus0 target 39 lun 0 (pass3,ses0) DM> <LSI CORP SAS2X36 0417> at scbus0 target 45 lun 0 (pass4,ses1) DM> <LSI CORP SAS2X36 0417> at scbus0 target 51 lun 0 (pass8,ses2) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 55 lun 0 (pass15,da7) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 63 lun 0 (pass16,da8) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 71 lun 0 (pass17,da9) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 79 lun 0 (pass18,da10) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 87 lun 0 (pass6,da11) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 95 lun 0 (pass20,da12) DM> <ATA WDC WD2003FYYS-0 1D01> at scbus0 target 103 lun 0 (pass21,da13)
Well, using http://kb.lsi.com/KnowledgebaseArticle16414.aspx I downgraded to version 8-fixed, and at least topology errors disappear. Just booted successfully (errm, it was a few nervous hours, to be honest :) Now I have in verbose kernel messages mps0: <LSI SAS2008> port 0xc000-0xc0ff mem 0xfb43c000-0xfb43ffff,0xfb440000-0xfb47ffff irq 16 at device 0.0 on pci2 mps0: Reserved 0x4000 bytes for rid 0x14 type 3 at 0xfb43c000 mps0: Firmware: 08.00.00.00 mps0: IOCCapabilities: 185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR> mps0: attempting to allocate 1 MSI-X vectors (15 supported) msi: routing MSI-X IRQ 256 to local APIC 0 vector 49 mps0: using IRQ 256 for MSI-X mps0: [MPSAFE] mps0: [ITHREAD] Will see whether it helps. -- Sincerely, D.Marck [DM5020, MCK-RIPE, DM3-RIPN] [ FreeBSD committer: ma...@freebsd.org ] ------------------------------------------------------------------------ *** Dmitry Morozovsky --- D.Marck --- Wild Woozle --- ma...@rinet.ru *** ------------------------------------------------------------------------ _______________________________________________ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"