TMK, On Fri, Feb 19, 2016 at 9:44 AM, Terry Kennedy <te...@glaver.org> wrote:
> > Can you get the status of the controller and disks via mptutil ? Also > > what does camcontrol devlist -v show ? > > 8.4 (8-STABLE): > > # mptutil show adapter > mpt0 Adapter: > Board Name: SAS6IR > Board Assembly: > Chip Name: C1068E > Chip Revision: UNUSED > RAID Levels: RAID0, RAID1, RAID1E > RAID0 Stripes: 64k > RAID1E Stripes: 64k > RAID0 Drives/Vol: 2-10 > RAID1 Drives/Vol: 2 > RAID1E Drives/Vol: 3-10 > > # mptutil show drives > mpt0 Physical Drives: > 0 ( 137G) ONLINE <SEAGATE ST3300657SS-H EH04> SAS bus 0 id 1 > 1 ( 137G) ONLINE <SEAGATE ST3300657SS-H EH04> SAS bus 0 id 9 > > # mptutil show volumes > mpt0 Volumes: > Id Size Level Stripe State Write-Cache Name > 0 ( 136G) RAID-1 OPTIMAL Enabled > > # camcontrol devlist -v > scbus0 on mpt0 bus 0: > <Dell VIRTUAL DISK 1028> at scbus0 target 0 lun 0 (da0,pass0) > <DP BACKPLANE 1.05> at scbus0 target 8 lun 0 (ses0,pass1) > <> at scbus0 target -1 lun -1 () > scbus1 on mpt0 bus 1: > <SEAGATE ST3300657SS-H EH04> at scbus1 target 0 lun 0 (pass2) > <> at scbus1 target -1 lun -1 () > scbus-1 on xpt0 bus 0: > <> at scbus-1 target -1 lun -1 (xpt0) > > 10.3-BETA2: > > # mptutil show adapter > mpt0 Adapter: > Board Name: SAS6IR > Board Assembly: > Chip Name: C1068E > Chip Revision: UNUSED > RAID Levels: RAID0, RAID1, RAID1E > RAID0 Stripes: 64K > RAID1E Stripes: 64K > RAID0 Drives/Vol: 2-10 > RAID1 Drives/Vol: 2 > RAID1E Drives/Vol: 3-10 > > # mptutil show drives > mpt0 Physical Drives: > 0 ( 137G) ONLINE <SEAGATE ST3300657SS-H EH04> SAS bus 0 id 1 > 1 ( 137G) ONLINE <SEAGATE ST3300657SS-H EH04> SAS bus 0 id 9 > > # mptutil show volumes > mpt0 Volumes: > Id Size Level Stripe State Write-Cache Name > 0 ( 136G) RAID-1 OPTIMAL Enabled > > # camcontrol devlist -v > scbus0 on mpt0 bus 0: > <Dell VIRTUAL DISK 1028> at scbus0 target 0 lun 0 (pass0,da0) > <DP BACKPLANE 1.05> at scbus0 target 8 lun 0 (ses0,pass1) > <> at scbus0 target -1 lun ffffffff () > scbus1 on mpt0 bus 1: > <SEAGATE ST3300657SS-H EH04> at scbus1 target 0 lun 0 (pass2) > <> at scbus1 target -1 lun ffffffff () > scbus2 on ata2 bus 0: > <TSSTcorp DVD-ROM TS-L333A D100> at scbus2 target 1 lun 0 (pass3,cd0) > <> at scbus2 target -1 lun ffffffff () > scbus3 on ata3 bus 0: > <> at scbus3 target -1 lun ffffffff () > scbus4 on ata4 bus 0: > <> at scbus4 target -1 lun ffffffff () > scbus5 on ata5 bus 0: > <> at scbus5 target -1 lun ffffffff () > scbus-1 on xpt0 bus 0: > <> at scbus-1 target -1 lun ffffffff (xpt0) > > To clarify, things seem to work fine on 10.3-BETA2 after the system > has booted, but there is a _long_ pause while the kernel is probing > the mpt0 controller, followed by the spew of CAM error messages from > the probes. > > Let me know if you need any additional info. > > Terry Kennedy http://www.glaver.org New York, NY USA > Can you build 10-STABLE and merge back the mpt driver prior to r285840 . It looks like a change was merged in about 7 weeks ago that has to do with probing the devices. https://svnweb.freebsd.org/base/stable/10/sys/dev/mpt/mpt.c?view=log <https://svnweb.freebsd.org/base?view=revision&revision=285840> -- mark saad | nones...@longcount.org _______________________________________________ freebsd-stable@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
