Hi,
I am getting the attached Fatal trap on shutdown.
Whenever I create a zfs pool I get the error.
eg: zpool create data da0s3a
I am running FreeBSD 7 on a Supermicro 5015M-MT+ running an Intel Core2 Duo
(E6700) CPU.
MB Ref:
http://www.supermicro.com/products/system/1U/5015/SYS-5015M-MT+.cfm
I am also using a hardware raid setup using a 3ware 9650SE series controller.
I have also attached dmesg output and fdisk output.
I have the system hooked up to serial console output, so if there is any
debugging steps that may help get to the bottom of this I should be able to
help.
I am trying to create the zfs pool on da0s3 or da0s3a - both cause the error.
Kind regards,
Geoff
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...1 1 1 1 0 0 0 done
All buffers synced.
Uptime: 50m27s
Fatal trap 12: page fault while in kernel mode
cpuid = 1; apic id = 01
fault virtual address = 0x0
fault code = supervisor write, page not present
instruction pointer = 0x20:0xc043f90d
stack pointer = 0x28:0xf2e9ebf4
frame pointer = 0x28:0xf2e9ec90
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 21 (swi2: cambio)
trap number = 12
panic: page fault
cpuid = 1
Uptime: 50m27s
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-BETA4 #0: Tue Dec 4 17:52:42 EST 2007
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/SERVER2
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 CPU 6700 @ 2.66GHz (2660.02-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
real memory = 3220045824 (3070 MB)
avail memory = 3149647872 (3003 MB)
ACPI APIC Table: <PTLTD APIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
kbd1 at kbdmux0
acpi0: <PTLTD RSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr a2a0a2a06000a2a
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr a2a0a2a06000a2a
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
3ware device driver for 9000 series storage controllers, version: 3.70.05.001
twa0: <3ware 9000 series Storage Controller> port 0x4000-0x40ff mem
0xe8000000-0xe9ffffff,0xea101000-0xea101fff,0xea100000-0xea100fff irq 16 at
device 0.0 on pci1
twa0: [ITHREAD]
twa0: INFO: (0x15: 0x1300): Controller details:: Model 9650SE-4LPML, 4 ports,
Firmware FE9X 3.06.00.003, BIOS BE9X 3.06.00.002
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci9: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci9
pci10: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0
pci13: <ACPI PCI bus> on pcib4
em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port 0x5000-0x501f
mem 0xea000000-0xea01ffff irq 16 at device 0.0 on pci13
em0: Using MSI interrupt
em0: Ethernet address: 00:30:48:8c:02:58
em0: [FILTER]
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
pci14: <ACPI PCI bus> on pcib5
em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port 0x6000-0x601f
mem 0xea200000-0xea21ffff irq 17 at device 0.0 on pci14
em1: Using MSI interrupt
em1: Ethernet address: 00:30:48:8c:02:59
em1: [FILTER]
uhci0: <UHCI (generic) USB controller> port 0x3000-0x301f irq 23 at device 29.0
on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x3020-0x303f irq 19 at device 29.1
on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x3040-0x305f irq 18 at device 29.2
on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x3060-0x307f irq 16 at device 29.3
on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xea700000-0xea7003ff
irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 8 ports with 8 removable, self powered
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci15: <ACPI PCI bus> on pcib6
vgapci0: <VGA-compatible display> port 0x7000-0x70ff mem
0xe0000000-0xe7ffffff,0xea400000-0xea40ffff irq 16 at device 0.0 on pci15
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x30a0-0x30af at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atapci1: <Intel ICH7 SATA300 controller> port
0x30e8-0x30ef,0x30dc-0x30df,0x30e0-0x30e7,0x30d8-0x30db,0x30b0-0x30bf mem
0xea700400-0xea7007ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
sio0: [FILTER]
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio1: [FILTER]
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xcc7ff pnpid ORM0000
on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
Timecounters tick every 1.000 msec
acd0: CDROM <CD-224E-N/1.AA> at ata0-master UDMA33
SMP: AP CPU #1 Launched!
da0 at twa0 bus 0 target 0 lun 0
da0: <AMCC 9650SE-4LP DISK 3.06> Fixed Direct Access SCSI-5 device
da0: 100.000MB/s transfers
da0: 238408MB (488259584 512 byte sectors: 255H 63S/T 30392C)
Trying to mount root from ufs:/dev/da0s1a
WARNING: ZFS is considered to be an experimental feature in FreeBSD.
ZFS filesystem version 6
ZFS storage pool version 6
em0: link state changed to UP
******* Working on device /dev/da0 *******
parameters extracted from in-core disklabel are:
cylinders=30392 heads=255 sectors/track=63 (16065 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=30392 heads=255 sectors/track=63 (16065 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 83875302 (40954 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 1023/ head 254/ sector 63
The data for partition 2 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 83875365, size 62910540 (30718 Meg), flag 0
beg: cyl 1023/ head 255/ sector 63;
end: cyl 1023/ head 254/ sector 63
The data for partition 3 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 146785905, size 341461575 (166729 Meg), flag 0
beg: cyl 1023/ head 255/ sector 63;
end: cyl 1023/ head 254/ sector 63
The data for partition 4 is:
<UNUSED>
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
