It looks like a system issue since it also happens to the SATA drive. The USB drive seems having more difficulty. I will back up rest partitions, Then redo the slice and partition to see if problem goes away. If so, then 8.0-R has a backward compatibility issue on the partition table or format to older FreeBSD release.
-----Original Message----- From: Hans Petter Selasky [mailto:hsela...@c2i.net] Sent: Wednesday, November 18, 2009 3:14 AM To: freebsd-usb@freebsd.org Cc: Guojun Jin; freebsd-sta...@freebsd.org; questi...@freebsd.org Subject: Re: 8.0-RC3 USB lock up on mounting two partitions from one USB drive Hi, I'm not sure if this is an USB issue or not. If you get READ/WRITE errors and the drive simply dies then it might be the case. Else it is a system issue. There are quirks for mass storage which you can add to sys/dev/usb/storage/umass.c . --HPS On Wednesday 18 November 2009 08:33:07 Guojun Jin wrote: > Did newfs on those partition and made things worsen -- restore completely > fails: (I had experienced another similar problem on an IDE, which works > well for 6.4 and 7.2, but 8.0.) This dirve works fine under FreeBSD 6.4. > > Is something new in 8.0 making disk partition schema changed? > > g_vfs_done():da0s3d[READ(offset=98304, length=16384)]error = 6 > g_vfs_done():da0s3d[WRITE(offset=192806912, length=16384)]error = 6 > fopen: Device not configured > cannot create save file ./restoresymtable for symbol table > abort? [yn] (da0:umass-sim0:0:0:0): Synchronize cache failed, status == > 0xa, scs i status == 0x0 > (da0:umass-sim0:0:0:0): removing device entry > ugen1.2: <DMI> at usbus1 > umass0: <DMI Ultra HDD, class 0/0, rev 2.00/1.19, addr 2> on usbus1 > umass0: SCSI over Bulk-Only; quirks = 0x0000 > umass0:0:0:-1: Attached to scbus0 > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <DMI Ultra HDD 1.19> Fixed Direct Access SCSI-0 device > da0: 40.000MB/s transfers > da0: 114473MB (234441648 512 byte sectors: 255H 63S/T 14593C) > Device da0s3d went missing before all of the data could be written to it; > expect data loss. > > 99 23:19 sysinstall > 100 23:20 newfs /dev/da0s3d > 101 23:20 newfs /dev/da0s3e > 102 23:21 mount /dev/da0s3d /mnt > 103 23:21 cd /mnt > 104 23:21 dump -0f - /home | restore -rf - > 105 23:27 history 15 > > > > -----Original Message----- > From: Guojun Jin > Sent: Tue 11/17/2009 11:05 PM > To: freebsd-sta...@freebsd.org > Cc: questi...@freebsd.org; freebsd-usb@freebsd.org > Subject: 8.0-RC3 USB lock up on mounting two partitions from one USB drive > > When mounting two partitions from a USB dirve, it can cause the drive > access lock up for a long time. Details: > > Terminal 1 -- > term1# mount /dev/da0s3d /mnt > term1# cd /mnt ; rm -fr * > > when rm starts, go to terminal 2 and do: > > term2# mount /dev/da0s3e /dist ### this will hanging for a long time and > USB hard drive activity light is off. After more than 1-2 minutes, mount > returns, and the drive activity light is blinking, thus removing is going > on. > > term2# ls /dist ### this will cause dUSB dirve hanging again -- no > avtivity. Similarly, ls will finish in a couple of miniutes or longer, the > rm command continues; but for a while, the drive activity will stop again. > > Reboot machine, repeat the above steps, and result will be the same. Reboot > machine again, and just mount one partition, then doing "rm -rf *" without > involve the second partition, rm will finish quickly. > > Has anyone obseved this behave on 8.0-RC? > > -Jin _______________________________________________ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "freebsd-usb-unsubscr...@freebsd.org"
