On 2023-06-13 18:57:13, Jessica Zhang wrote: > DSI 6G v2.5.x+ supports a data-bus widen mode that allows DSI to send > 48 bits of compressed data per pclk instead of 24. > > For all chipsets that support this mode, enable it whenever DSC is > enabled as recommend by the hardware programming guide. > > Only enable this for command mode as we are currently unable to validate > it for video mode. > > Signed-off-by: Jessica Zhang <quic_jessz...@quicinc.com> > --- > > Note: The dsi.xml.h changes were generated using the headergen2 script in > envytools [1], but the changes to the copyright and rules-ng-ng source file > paths were dropped. > > [1] https://github.com/freedreno/envytools/
More interesting would be a link to the Mesa MR upstreaming this bitfield to dsi.xml [2] (which I have not found on my own yet). [2]: https://gitlab.freedesktop.org/mesa/mesa/-/blame/main/src/freedreno/registers/dsi/dsi.xml > drivers/gpu/drm/msm/dsi/dsi.xml.h | 1 + > drivers/gpu/drm/msm/dsi/dsi_host.c | 19 ++++++++++++++++++- > 2 files changed, 19 insertions(+), 1 deletion(-) > > diff --git a/drivers/gpu/drm/msm/dsi/dsi.xml.h > b/drivers/gpu/drm/msm/dsi/dsi.xml.h > index a4a154601114..2a7d980e12c3 100644 > --- a/drivers/gpu/drm/msm/dsi/dsi.xml.h > +++ b/drivers/gpu/drm/msm/dsi/dsi.xml.h > @@ -664,6 +664,7 @@ static inline uint32_t > DSI_CMD_MODE_MDP_CTRL2_INPUT_RGB_SWAP(enum dsi_rgb_swap v > return ((val) << DSI_CMD_MODE_MDP_CTRL2_INPUT_RGB_SWAP__SHIFT) & > DSI_CMD_MODE_MDP_CTRL2_INPUT_RGB_SWAP__MASK; > } > #define DSI_CMD_MODE_MDP_CTRL2_BURST_MODE 0x00010000 > +#define DSI_CMD_MODE_MDP_CTRL2_DATABUS_WIDEN 0x00100000 > > #define REG_DSI_CMD_MODE_MDP_STREAM2_CTRL 0x000001b8 > #define DSI_CMD_MODE_MDP_STREAM2_CTRL_DATA_TYPE__MASK > 0x0000003f > diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c > b/drivers/gpu/drm/msm/dsi/dsi_host.c > index 5d7b4409e4e9..1da5238e7105 100644 > --- a/drivers/gpu/drm/msm/dsi/dsi_host.c > +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c > @@ -927,6 +927,9 @@ static void dsi_timing_setup(struct msm_dsi_host > *msm_host, bool is_bonded_dsi) > u32 hdisplay = mode->hdisplay; > u32 wc; > int ret; > + bool widebus_supported = msm_host->cfg_hnd->major == > MSM_DSI_VER_MAJOR_6G && > + msm_host->cfg_hnd->minor >= MSM_DSI_6G_VER_MINOR_V2_5_0; > + > > DBG(""); > > @@ -973,8 +976,15 @@ static void dsi_timing_setup(struct msm_dsi_host > *msm_host, bool is_bonded_dsi) > * > * hdisplay will be divided by 3 here to account for the fact > * that DPU sends 3 bytes per pclk cycle to DSI. > + * > + * If widebus is supported, set DATABUS_WIDEN register and > divide hdisplay by 6 > + * instead of 3 So this should allow us to divide pclk by 2, or have much lower latency? Otherwise it'll tick enough times to transmit the data twice. Note that I brought up the exact same concerns when you used the 3:1 ratio from dsi_bpp / dsc_bpp in your pclk reduction patch (instad of the number of bits/bytes that DPU sends to DSI per pclk), but no-one has replied to my inquiry yet. > */ > - hdisplay = > DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 3); > + if (!(msm_host->mode_flags & MIPI_DSI_MODE_VIDEO) && > widebus_supported) > + hdisplay = > DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 6); > + else > + hdisplay = > DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), 3); Nit: I wonder if this is more concise when written as: u32 bytes_per_pclk; ... if (!video && widebus) bytes_per_pclk = 6; else bytes_per_pclk = 3; hdisplay = DIV_ROUND_UP(msm_dsc_get_bytes_per_line(msm_host->dsc), bytes_per_pclk); That is less duplication, **and** the value becomes self-documenting! > + > h_total += hdisplay; > ha_end = ha_start + hdisplay; > } > @@ -1027,6 +1037,13 @@ static void dsi_timing_setup(struct msm_dsi_host > *msm_host, bool is_bonded_dsi) > dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL, > DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) | > DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay)); > + > + if (msm_host->dsc && widebus_supported) { Can we also support widebus for uncompressed streams (sending 2 pixels of bpp=24 per pclk), and if so, is that something you want to add in the future (a comment would be nice)? > + u32 mdp_ctrl2 = dsi_read(msm_host, > REG_DSI_CMD_MODE_MDP_CTRL2); > + > + mdp_ctrl2 |= DSI_CMD_MODE_MDP_CTRL2_DATABUS_WIDEN; > + dsi_write(msm_host, REG_DSI_CMD_MODE_MDP_CTRL2, > mdp_ctrl2); > + } Same comment as on your BURST_MODE patch (which this'll conflict with): does this belong to the timing setup or is it better moved to dsi_ctrl_config? - Marijn > } > } > > > -- > 2.40.1 >
