I'm using Windows XP, the same as for eap/tls and it worked fine in that case. My card is a 350 cisco and follow the instructions in the cisco page to configure it as well as the AP. In teh network manager I enabled PEAP auth and unchecked the box you mentioned about using my windows login to auth. Anyway the user sent to the radius is not my login!!! any idea?
bfr ----- Mensaje original ----- De: Bob McCormick <[EMAIL PROTECTED]> Fecha: Lunes, Mayo 24, 2004 6:42 pm Asunto: Re: peap user > Sounds like a client side problem. What supplicant are you > using? > Are you using the one built into Win2k or WinXP? Both of those > have > checkboxes to automatically use your machine name or your windows > login > name. Make sure those aren't checked. > > > On May 24, 2004, at 10:33 AM, BLANCA FERRERO RODRIGUEZ wrote: > > > Hi, > > > > I'm configuring PEAP. I think the freeradius config is Ok. I'm > using > > an Aironet AP 1100 configured to support 802.1X authentication > and > > WEP and my wireless network is enabled to use PEAP auth. > > the fact is that when I try to authenticate my card against > radius I'm > > not asked to enter a user and a passw and it directly uses an > unknown > > user for me called PEAP-mi_card_MAC. Wasn't I suppossed to de > asked to > > enter the user? > > > > I add the logs in case they can help. > > thanks a lot > > > > bfr > > > > rad_recv: Access-Request packet from host 172.26.0.3:1645, id=6, > > length=161 > > User-Name = "PEAP-000CCE21141B" > > Framed-MTU = 1400 > > Called-Station-Id = "0040.96a0.19dc" > > Calling-Station-Id = "000c.ce21.141b" > > NAS-Port-Type = Wireless-802.11 > > Message-Authenticator = 0x642163f9e77208900dc76dd8c5b48981 > > EAP-Message = 0x0202001601504541502d303030434345323131343142 > > NAS-Port-Type = Virtual > > NAS-Port = 63 > > Service-Type = Login-User > > NAS-IP-Address = 172.26.0.3 > > NAS-Identifier = "ap_cisco " > > Processing the authorize section of radiusd.conf > > modcall: entering group authorize for request 0 > > modcall[authorize]: module "preprocess" returns ok for request 0 > > modcall[authorize]: module "chap" returns noop for request 0 > > modcall[authorize]: module "mschap" returns noop for request 0 > > rlm_realm: No '@' in User-Name = "PEAP-000CCE21141B", > looking up > > realm NULL > > rlm_realm: No such realm "NULL" > > modcall[authorize]: module "suffix" returns noop for request 0 > > rlm_eap: EAP packet type response id 2 length 22 > > rlm_eap: No EAP Start, assuming it's an on-going EAP conversation > > modcall[authorize]: module "eap" returns updated for request 0 > > users: Matched DEFAULT at 177 > > modcall[authorize]: module "files" returns ok for request 0 > > modcall: group authorize returns updated for request 0 > > rad_check_password: Found Auth-Type Reject > > rad_check_password: Auth-Type = Reject, rejecting user > > auth: Failed to validate the user. > > Delaying request 0 for 1 seconds > > Finished request 0 > > Going to the next request > > --- Walking the entire request list --- > > Waking up in 1 seconds... > > --- Walking the entire request list --- > > Waking up in 1 seconds... > > --- Walking the entire request list --- > > Sending Access-Reject of id 6 to 172.26.0.3:1645 > > Waking up in 4 seconds... > > --- Walking the entire request list --- > > Cleaning up request 0 ID 6 with timestamp 40b22f94 > > Nothing to do. Sleeping until we see a request. > > rad_recv: Access-Request packet from host 172.26.0.3:1645, id=7, > > length=161 > > User-Name = "PEAP-000CCE21141B" > > Framed-MTU = 1400 > > Called-Station-Id = "0040.96a0.19dc" > > Calling-Station-Id = "000c.ce21.141b" > > NAS-Port-Type = Wireless-802.11 > > Message-Authenticator = 0xbabd2bd7b3b9a2cf23018d052dcc7582 > > EAP-Message = 0x0201001601504541502d303030434345323131343142 > > NAS-Port-Type = Virtual > > NAS-Port = 64 > > Service-Type = Login-User > > NAS-IP-Address = 172.26.0.3 > > NAS-Identifier = "ap_cisco " > > Processing the authorize section of radiusd.conf > > modcall: entering group authorize for request 1 > > modcall[authorize]: module "preprocess" returns ok for request 1 > > modcall[authorize]: module "chap" returns noop for request 1 > > modcall[authorize]: module "mschap" returns noop for request 1 > > rlm_realm: No '@' in User-Name = "PEAP-000CCE21141B", > looking up > > realm NULL > > rlm_realm: No such realm "NULL" > > modcall[authorize]: module "suffix" returns noop for request 1 > > rlm_eap: EAP packet type response id 1 length 22 > > rlm_eap: No EAP Start, assuming it's an on-going EAP conversation > > modcall[authorize]: module "eap" returns updated for request 1 > > users: Matched DEFAULT at 177 > > modcall[authorize]: module "files" returns ok for request 1 > > modcall: group authorize returns updated for request 1 > > rad_check_password: Found Auth-Type Reject > > rad_check_password: Auth-Type = Reject, rejecting user > > auth: Failed to validate the user. > > Delaying request 1 for 1 seconds > > Finished request 1 > > Going to the next request > > --- Walking the entire request list --- > > Waking up in 1 seconds... > > --- Walking the entire request list --- > > Waking up in 1 seconds... > > --- Walking the entire request list --- > > Sending Access-Reject of id 7 to 172.26.0.3:1645 > > Waking up in 4 seconds... > > --- Walking the entire request list --- > > Cleaning up request 1 ID 7 with timestamp 40b22f9f > > Nothing to do. Sleeping until we see a request. > > rad_recv: Access-Request packet from host 172.26.0.3:1645, id=8, > > length=161 > > User-Name = "PEAP-000CCE21141B" > > Framed-MTU = 1400 > > Called-Station-Id = "0040.96a0.19dc" > > Calling-Station-Id = "000c.ce21.141b" > > NAS-Port-Type = Wireless-802.11 > > Message-Authenticator = 0x017eb94e1149c58524647d0840f81dce > > EAP-Message = 0x0201001601504541502d303030434345323131343142 > > NAS-Port-Type = Virtual > > NAS-Port = 65 > > Service-Type = Login-User > > NAS-IP-Address = 172.26.0.3 > > NAS-Identifier = "ap_cisco " > > Processing the authorize section of radiusd.conf > > modcall: entering group authorize for request 2 > > modcall[authorize]: module "preprocess" returns ok for request 2 > > modcall[authorize]: module "chap" returns noop for request 2 > > modcall[authorize]: module "mschap" returns noop for request 2 > > rlm_realm: No '@' in User-Name = "PEAP-000CCE21141B", > looking up > > realm NULL > > rlm_realm: No such realm "NULL" > > modcall[authorize]: module "suffix" returns noop for request 2 > > rlm_eap: EAP packet type response id 1 length 22 > > rlm_eap: No EAP Start, assuming it's an on-going EAP conversation > > modcall[authorize]: module "eap" returns updated for request 2 > > users: Matched DEFAULT at 177 > > modcall[authorize]: module "files" returns ok for request 2 > > modcall: group authorize returns updated for request 2 > > rad_check_password: Found Auth-Type Reject > > rad_check_password: Auth-Type = Reject, rejecting user > > auth: Failed to validate the user. > > Delaying request 2 for 1 seconds > > Finished request 2 > > Going to the next request > > --- Walking the entire request list --- > > Waking up in 1 seconds... > > --- Walking the entire request list --- > > Waking up in 1 seconds... > > --- Walking the entire request list --- > > Sending Access-Reject of id 8 to 172.26.0.3:1645 > > Waking up in 4 seconds... > > --- Walking the entire request list --- > > Cleaning up request 2 ID 8 with timestamp 40b22faa > > Nothing to do. Sleeping until we see a request. > > > > > > > > - > > List info/subscribe/unsubscribe? See > > http://www.freeradius.org/list/users.html > > > > - > List info/subscribe/unsubscribe? See > http://www.freeradius.org/list/users.html - List info/subscribe/unsubscribe? See http://www.freeradius.org/list/users.html
