Evgeniy, I will need some time to digest all of this. I have an a104 but I don't have a solaris system for testing. I will report back as soon as I can.
-MC On Dec 5, 2008, at 6:53 AM, Evgeniy Zolotov <[EMAIL PROTECTED]> wrote: > Greetings! > > Question about possibility of the use FreeSWITCH for work with T1/E1 > streams under Sun Solaris 10 a bit clears up (Solaris 11 is in > condition > of alpha-version and not suitable for the industrial use). But answers > carry more negative sense. > > Start of T1/E1 under Sun Solaris has 2 stages: a) start of wanpipe's > interface; b) make FreeSWITCH for Sun Solaris. > > > a) For Linux Sangoma recommends > (http://wiki.sangoma.com/wanpipe-freeswitch-install) installation of > new > interface wanpipe-3.3.14.tgz, which has beta-status and placed at > ftp://ftp.sangoma.com/linux/current_wanpipe. > > This installation and tests were successful. > > In this release (2007 y.) by Sangoma was added TDM API - native > interface for FreeSwitch (YATE) — which is absent in all previous > releases of WANPIPE. In the Linux release 3.3.14 this variant was > named > as «TDM API», in older releases - «TDM Voice». > > In this case FreeSWITCH works very good with E1/T1 cards > A-101/102/104/108 without installation in zaptel system, and spans in > configuration files of FreeSWITCH declared as [wanpipe#]. > > But for Sun Solaris we found only > drverftp://ftp.sangoma.com/Solaris/Beta/SVwanpipe-i386-5.10.pkgbeta, > which dated 2007: > >> NAME=sangoma.com Wanpipe Driver > >> VERSION=1.1.0,REV=2007-07-16, > > Packet Svwanpipe-i386-5.10.pkg uses Svzaptel-i386-5.10.pkg, which > wasn't > developed by Sangoma, but by little free > communityhttp://www.solarisvoip.com/, source codes of this packet is > herehttps://svn.sunlabs.com/svn/solaris-asterisk/zaptel-solaris/trunk/ > > The analysis of source codes shows that this project develops very > slowly (there are no updates for about year), has very limited > functionality and supports ( unlike original zaptel ) very limited > list > of cards ( only one ;) - Digium Wildcard TE110P T1/PRI). > > Svwanpipe-i386-5.10.pkg supports only 64-bit Sun Solaris (on CD, which > we get with Sangoma's cards, presents 32-bit driver and PDF document > about installation under Sun Solaris — but it dated 2001 — 2002 yy > ). > > At first we have checked up installation with TDM Voice + zaptel (like > for Asterisk) under Linux. We configured PRI spans as [zt] ... - such > installation works good and we could do calls : > > >> originate openzap/1/A/20000 &sleep(3) > > > * evidently that call retranslates from span 1 to span 2, > connected with cross-cable, and goes to extension 20000. > > > > b) About making FreeSwitch: > > Under Sun Solaris 10 with GCC makes FreeSWITCH core and most modules, > except openzapand some others, because Sun Solaris 10 has GCC 3.4, > but ./configure for openzap requires compatibility with ANSII 99. > > We have checked 3 different methods of makinf FreeSWITCH : > > > 1. set up GCC 4.0.2 from CSW-repositaries (and all reguired for GCC > *.pkg); > > 2. set up SunStudio 12 and do make cc/CC; > > 3.cross-compile FreeSwitch for Sun Solaris under Linux with CC- > options. > > > In testing we used assembly SunStudio as 32-bit application (64-bit > comes to the end with mistakes of assembly of some libraries, it is > possible to correct for it easily, but we did not begin to specify > it). > > > For testing cards A-104 we have repeated the same installation and > configuring as under Linux (wanpipe TDM Voice + zaptel) on 4 different > 64-bit servers under Sun Solaris 10: > > > * on 3 servers (2 of them manufactured by SUN) executed > successfully : # wanrouter start > > > > 4 wanrouter# interfaces was created; leds on spans, connected with > cross-cable, becomes GREEN, i.e. synchronization T1/E1 presents (no > alarms). > > On these servers FreeSWITCH correctly makes: > > >> load mod_openzap > > > * but when we make : > > > >> originate openzap/1/A/20000 &sleep(3) > > > - for 2 connected with crosss-cable spans (1 & 2) FreeSWITCH transmits > PRI message (chan 1/31), but chan 2/31 doesn't receive this message > (unlike under Linux) and call breaks after timeout. > > On 4-th server wanpipe doesn't even starts by mistake some IOCTL (i.e. > at a command for device). Three «working» servers is on AMD Opteron > Dual > Core 2214(F), fourth is on ntel Xeon 3210. > > So, we supposes Svwanpipe-i386-5.10.pkg or Svzaptel-i386-5.10.pkg from > Sangoma checked up a little and on some one processor and doesn't > heave > up even on beta, as they are declared, at the best on alpha > > > What's the reason of error??? > > * wanpipe doesn't work under Solaris? > > * wrong working signalling with zaptel? (but same configuration > works good under Linux) > > * wrong working of FreeSWITCH, which was built correctly, but > their work was violated? > * > * > Thanks, Evgeniy. > > > > > _______________________________________________ > Freeswitch-users mailing list > [email protected] > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users > UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users > http://www.freeswitch.org _______________________________________________ Freeswitch-users mailing list [email protected] http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
