Hi , I'm curious, what is the default mode SPLAT HA is in broadcast or multicast?
Colin Choo >> -----Original Message----- >> From: Mailing list for discussion of Firewall-1 [mailto:FW-1- >> [EMAIL PROTECTED] On Behalf Of Previtera, Sal >> Sent: Friday, September 17, 2004 1:39 AM >> To: [EMAIL PROTECTED] >> Subject: Re: [FW-1] FLAPPING CROSSOVER >> >> The problem is multicast and the type of Switch you are using >> Try Broadcast instead, at the firewalls (both of them) issue the >> following >> commands; >> >> cphaconf set_ccp broadcast (change to broadcast mode) >> >> cphaprob -a if (see if all interface are using broadcast) >> >> If you do want to use broadcast, then you have to figure out why the >> multicast version of Checkpoint and the Switch Vendor version are >> incompatible. >> >> >> >> -----Original Message----- >> From: Torkel Mathisen [mailto:[EMAIL PROTECTED] >> Sent: Thursday, September 16, 2004 10:03 AM >> To: [EMAIL PROTECTED] >> Subject: Re: [FW-1] FLAPPING CROSSOVER >> >> Hi >> >> We also got some problems with flapping crossover or atleast >> clusterxl. >> >> It may or not be the same problem as this. >> >> In our log we see this all the time: >> >> cluster_info: (ClusterXL) Interface Active Check on member 2 >> (10.254.254.2) >> detected a problem (5 interfaces required, only 4 up). >> cluster_info: (ClusterXL) interface eth3 of member 2 (10.254.254.2) is >> down >> (receive down, transmit down) >> cluster_info: (ClusterXL) Interface Active Check on member 2 >> (10.254.254.2) >> status OK. >> cluster_info: (ClusterXL) member 2 (10.254.254.2) is up. >> cluster_info: (ClusterXL) member 2 (10.254.254.2) is standby. >> cluster_info: (ClusterXL) interface eth3 of member 2 (10.254.254.2) is up >> >> A bit futher down (or just a little bit before, depending on >> how you look at it) we get: >> cluster_info: (ClusterXL) member 2 (10.254.254.2) is down. >> >> Note that the sync-interface is NOT eth3 so it actually reports >> down on another interface. >> >> You see something like that in your logs Annette? >> >> And does anyone have an idea? >> >> Cluster running SPLAT R55 121 with Checkpoint HA only. >> Interfaces is Intel e1000 which is autonegotiated to 1000 full. >> >> Regards, >> Torkel >> >> >> > -----Original Message----- >> > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] >> > Sent: 15. september 2004 15:31 >> > To: [EMAIL PROTECTED] >> > Subject: Re: [FW-1] FLAPPING CROSSOVER >> > >> > >> > Are you running ClusterXL, or other? What OS? There are quite >> > a few bugs I >> > know of in just ClusterXL alone with synch... >> > Perhaps I may be able to help you. Let the mailing list know. :-) >> > >> > >> > Regards, >> > Matt Goddard >> > Security Information Team >> > Schneider National >> > 920-592-4787 >> > [EMAIL PROTECTED] >> > >> > >> > >> > |---------+--------------------------------------------> >> > | | "Garner, Annette K **BETH" | >> > | | <[EMAIL PROTECTED]> | >> > | | Sent by: Mailing list for | >> > | | discussion of Firewall-1 | >> > | | <[EMAIL PROTECTED]| >> > | | KPOINT.COM> | >> > | | | >> > | | | >> > | | 09/15/2004 06:18 AM | >> > | | Please respond to Mailing list | >> > | | for discussion of Firewall-1 | >> > | | | >> > |---------+--------------------------------------------> >> > >> > >------------------------------------------------------------- >> > ---------------------------------| >> > | >> > | >> > | To: >> > [EMAIL PROTECTED] >> > | >> > | cc: >> > | >> > | Subject: [FW-1] FLAPPING CROSSOVER >> > | >> > >> > >------------------------------------------------------------- >> > ---------------------------------| >> > >> > >> > >> > >> > I have swapped out the cable and switched to a new nic with >> > the no luck. >> > I turned off auto-negotiated and set it to 100baseTX-FD >> > flow-control on >> > both boxes. >> > >> > >> > >> > Thanks, >> > >> > Annette >> > >> > >> > ================================================= >> > To set vacation, Out-Of-Office, or away messages, >> > send an email to [EMAIL PROTECTED] >> > in the BODY of the email add: >> > set fw-1-mailinglist nomail >> > ================================================= >> > To unsubscribe from this mailing list, >> > please see the instructions at >> > http://www.checkpoint.com/services/mailing.html >> > ================================================= >> > If you have any questions on how to change your >> > subscription options, email >> > [EMAIL PROTECTED] >> > ================================================= >> > >> > ================================================= >> > To set vacation, Out-Of-Office, or away messages, >> > send an email to [EMAIL PROTECTED] >> > in the BODY of the email add: >> > set fw-1-mailinglist nomail >> > ================================================= >> > To unsubscribe from this mailing list, >> > please see the instructions at >> > http://www.checkpoint.com/services/mailing.html >> > ================================================= >> > If you have any questions on how to change your >> > subscription options, email >> > [EMAIL PROTECTED] >> > ================================================= >> > >> >> ================================================= >> To set vacation, Out-Of-Office, or away messages, >> send an email to [EMAIL PROTECTED] >> in the BODY of the email add: >> set fw-1-mailinglist nomail >> ================================================= >> To unsubscribe from this mailing list, >> please see the instructions at >> http://www.checkpoint.com/services/mailing.html >> ================================================= >> If you have any questions on how to change your >> subscription options, email >> [EMAIL PROTECTED] >> ================================================= >> >> ================================================= >> To set vacation, Out-Of-Office, or away messages, >> send an email to [EMAIL PROTECTED] >> in the BODY of the email add: >> set fw-1-mailinglist nomail >> ================================================= >> To unsubscribe from this mailing list, >> please see the instructions at >> http://www.checkpoint.com/services/mailing.html >> ================================================= >> If you have any questions on how to change your >> subscription options, email >> [EMAIL PROTECTED] >> ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
