You cannot change a from Static NAT to Hide Nat so careless, Static NAT Should be there to gather the access from the internet to the corporate network, you should verify that, or better yet, create a network and use hide nat.
On 9/21/07, Michael Vaillancourt <[EMAIL PROTECTED]> wrote: > > If its a manual NAT rule, Under the NAT tab in the dashboard, under the > translated side of the NAT rule, right click the object and change it from > a > STATIC NAT to a HIDE NAT. > > If the NAT rule was created using the automatic NAT method. Edit the > object > the NAT was configured on, click the NAT tab, and make sure Hide is chosen > instead of Static > > After either change you will need to install policy. > > On 9/21/07, Elvis Ademba <[EMAIL PROTECTED]> wrote: > > > > i can confirm the fisrt ip was a static NAT. > > but since there are now two IPs ... > > > > How do i do dynamic nat. > > whats the command / commands. > > bear in mind there are other internal ip addresss using dynamic nat but > a > > diffrent Public IP Address. > > Just this two need to use this one Ip address because of the services > they > > are running. > > > > regards > > Elvis > > ............................................... > > ................................................ > > > > On 9/21/07, Jose Valdivia <[EMAIL PROTECTED]> wrote: > > > > > > that can be, a wrong type of nat. > > > > > > You should be using a Dynamic Nat, or checkpoint's name hide nat, if > > works > > > with only one ip that maybe because you're using a static nat, you > have > > to > > > put more information, about how you are doing it. > > > > > > Regards. > > > -- > > > > > > On 9/21/07, Elvis Ademba <[EMAIL PROTECTED]> wrote: > > > > > > > > I have a question about firewalls. > > > > > > > > We have been trying to configure two internal IP addresses to use > one > > > > Public > > > > IP address when going outside. > > > > but only one IP works the other doesnt. > > > > the rest of the computers in the organization use a different IP to > go > > > out > > > > so no problem there. Just these two PCs need to use one Public ip > > while > > > > going out. > > > > > > > > Please help whats the command. > > > > Cisco PIX > > > > > > > > Regards > > > > Elvis > > > > ....................................... > > > > > > > > ================================================= > > > > To set vacation, Out-Of-Office, or away messages, > > > > send an email to [EMAIL PROTECTED] > > > > in the BODY of the email add: > > > > set fw-1-mailinglist nomail > > > > ================================================= > > > > To unsubscribe from this mailing list, > > > > please see the instructions at > > > > http://www.checkpoint.com/services/mailing.html > > > > ================================================= > > > > If you have any questions on how to change your > > > > subscription options, email > > > > [EMAIL PROTECTED] > > > > ================================================= > > > > > > > > > > > > > > > > -- > > > Jose Valdivia > > > Firewall Enginner > > > > > > Perot Systems > > > CCSA CCSE WCSA NCMA NCMP > > > > > > ================================================= > > > To set vacation, Out-Of-Office, or away messages, > > > send an email to [EMAIL PROTECTED] > > > in the BODY of the email add: > > > set fw-1-mailinglist nomail > > > ================================================= > > > To unsubscribe from this mailing list, > > > please see the instructions at > > > http://www.checkpoint.com/services/mailing.html > > > ================================================= > > > If you have any questions on how to change your > > > subscription options, email > > > [EMAIL PROTECTED] > > > ================================================= > > > > > > > ================================================= > > To set vacation, Out-Of-Office, or away messages, > > send an email to [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, > > please see the instructions at > > http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your > > subscription options, email > > [EMAIL PROTECTED] > > ================================================= > > > > ================================================= > To set vacation, Out-Of-Office, or away messages, > send an email to [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, > please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your > subscription options, email > [EMAIL PROTECTED] > ================================================= > -- Jose Valdivia Firewall Enginner Perot Systems CCSA CCSE WCSA NCMA NCMP ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
