Hi,
the information i have collected so far is
My workstations LAN connection seems 1 G (interface is at
autonegation), and also the interface of firewall im having connection
problems seems to work at 1 G (i looked at with ethtool eth1)
ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Link detected: yes
Also i went to the firewalls console for an other try i try to ping my
PC didnt work. I gave fw unloadlocal and then pinged works fine and i
was able to connect with ssh to the firewall and ping the firewall
from PC but it also stopped? And while i was writing this sentence it
started pinging again and i opened the dashboard but i dont think it
will last for sor long. I will look for more information youll asked
for.
Regards
2011/12/19 Hugo van der Kooij <[email protected]>:
>
>
> On 19.12.2011 09:12, a bv wrote:
>
>> I have made a clean R75.20
> SPLAT installation on a box and made 1 IP
>> up with LAN IP and since its
> not connected to other networks and still
>> testing made a rule with any
> any accept on it. I work on with both
>> Smartdashboard , ssh,webui etc.
> But i sometimes get disconnected from
>> them and im pinging the gateway
> (since it accepts) and those times i
>> cant get reply to my ping
> requests. If i have time i go to the
>> firewalls side physically and on
> the shell i ping my workstation well.
>> So what do you think the reason
> can be? Of course i want this to be a
>> stable firewall and if not
> necessary doesnt wanna reinstall.
>
> Round up the usual suspects:
>
> Run
> `netstat -ni;sleep 60;netstat -ni` ==> Check for interface errors that
> increase.
>
> Check with ethtool if the interface is not set to
> half-duplex while the other side is set to full-duplex.
>
> Check
> /var/log/messages, $CPDIR/log/*.elg and $FWDIR/log/*.elg for anomalies.
>
>
> Check ARP tables with `arp -a` and `fw ctl arp`.
>
> If shaking down
> these suspects is not clearly pointing towards a suspect that you can
> fix then share these findings with the rest so further advise can be
> given based upon these findings.
>
> --
> [email protected]
> http://hugo.vanderkooij.org/
> PGP/GPG? Use:
> http://hugo.vanderkooij.org/0x58F19981.asc
>
>
> Scanned by Check Point Total Security Gateway.
>
> =================================================
> To set vacation, Out-Of-Office, or away messages,
> send an email to [email protected]
> in the BODY of the email add:
> set fw-1-mailinglist nomail
> =================================================
> To unsubscribe from this mailing list,
> please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> =================================================
> If you have any questions on how to change your
> subscription options, email
> [email protected]
> =================================================
Scanned by Check Point Total Security Gateway.
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
