Hello, Only allowing subnet a.b.*.* through the policy is not enough, you must also allow the clients one by one, they are listed in a file called gui-clients and are added to the file by running cpconfig.
Met vriendelijke groeten - Bien � vous - Kind regards Guy ROELANDTS EMEA GS Internet Expertise Centre - CCSA & CCSE Compaq Software Engineer - Belgium E-mail : [EMAIL PROTECTED] Tel: +32(02)729.77.44 (options 3 - 3 - 1) Fax: +32(02)729.77.65 ========================================================== This message may contain confidential and/or proprietary information, and is intended only for the person/entity to whom it was originally addressed. The content of this message may contain private views and opinions which do not constitute a formal disclosure or commitment unless specifically stated. Should you receive this message by mistake please inform the sender immediately. ========================================================== -----Original Message----- From: Ercan AYDEMIR [mailto:[EMAIL PROTECTED]] Sent: 11 April 2002 14:48 To: [EMAIL PROTECTED] Subject: Re: [FW-1] pb to access to management console from a GUI The second workstation is also in the subnet a.b.c.* As I have allowed the subnet a.b.*.* to access to the management station, it should work. But it doesn't !!! Theo van den Beld <[EMAIL PROTECTED]> To: [EMAIL PROTECTED] Sent by: Mailing list for discussion cc: of Firewall-1 Subject: Re: [FW-1] pb to access to management console from a GUI <[EMAIL PROTECTED] point.com> 04/11/02 01:33 PM Please respond to Mailing list for discussion of Firewall-1 Check your gui-clients file and check if the 2nd workstation is allowed. Regards, Theo -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED]]On Behalf Of Ercan AYDEMIR Sent: Thursday, April 11, 2002 12:13 PM To: [EMAIL PROTECTED] Subject: [FW-1] pb to access to management console from a GUI Hi everybody, I have installed the GUI on two PCs which are on the same subnet (a.b.c.0/128). When I use the first one, I can access to the FW management console (e.f.g.h) using the GUI. But When I do it from the second PC, I have the message "Authentication to server e.f.g.h failed" On the management console, I have used cpconfig to enable the subnet a.b.*. * to access to the management console. What might be wrong ?? thanks for your help. ================================================= To set vacation, Out Of Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
