Hi Carlos Lopez You can not do anything. You can only have one default router. So you can solve your problem with dynamic routing, or static routing adding some manual routes.
-----Mensaje original----- De: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED]]En nombre de Carlos Lopez Enviado el: jueves, 03 de octubre de 2002 22:31 Para: [EMAIL PROTECTED] Asunto: Re: [FW-1] Two different Internet connections in the same machine Exists one probem. i have one router to connect to internet (default gateway for the firewall) and the another router is the adsl .... Can I do it even ?? >sorry, i gave this some thought and it might be a >little bit more >complicated. i think the best option would be to have >the following: >lan connected to firewall. firewall outside int >connects to a router with >2x eth ports and 1x ser port. one eth port into >firewall and other into >adsl router. ser line to isp. >on the lan side you'll have the same default >gateway...the firewall. >you'll have a static route, to route the adsl user >lan ip(Y) to an ip >address >that is on the adsl eth range(X). on the the router >you'll do policy based >routing. something along the lines of when a packet >comes from X, the >lan_adsl_user's nat address, pump the packet out on >the adsl port, if it's >anything else, use the default gateway, which is the >serial port. you will >also have to add either a static route on the router >for ip address X to >get back to the firewall or do a proxy arp on the >firewall for ip address >X. >sorry i'm in a bit of a hurry. so let me know if it >doesn't make any >sense. >cheers >andre' --- andre <[EMAIL PROTECTED]> escribi�: > You should be able to do this based on nat > configuration. you can add a > static nat entry that will nat the internal machine > to an ip that is > valid on your adsl interface. > > just a thought > > andre' > > On Fri, 27 Sep 2002, [iso-8859-1] Carlos Lopez > wrote: > > > Hi all, > > > > I have a nokia ip330 with ipso 3.5fcs7 ant NG > FP2 > > installed with five nic cards. One to internet, > > another to lan, another to dmz1, another to dmz2 > and > > another to an ADSL router. My question is: Is it > > possible to make only one machine in the internal > > network use the ADSL to surf the net instead the > > default route without using BGP or OSPF, etc??. Is > it > > possible to do this with firewall NG rules ???. > > > > > > Thank you very much and sorry for my poor english. > > > > > > > _________________________________________________________ > > Do You Yahoo!? > > Informaci�n de Estados Unidos y Am�rica Latina, en > Yahoo! Noticias. > > Vis�tanos en http://noticias.espanol.yahoo.com > > > > ================================================= > > To set vacation, Out Of Office, or away messages, > > send an email to [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, > > please see the instructions at > > http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your > > subscription options, email > > [EMAIL PROTECTED] > > ================================================= > > > > ================================================= > To set vacation, Out Of Office, or away messages, > send an email to [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, > please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your > subscription options, email > [EMAIL PROTECTED] > ================================================= _________________________________________________________ Do You Yahoo!? Informaci�n de Estados Unidos y Am�rica Latina, en Yahoo! Noticias. Vis�tanos en http://noticias.espanol.yahoo.com ================================================= To set vacation, Out Of Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
