Dear Haeyoon Cho, I mean the terminal which I type command line.
I know that the echo command writes statement on the terminal which I type command lines. By the way, what do you mean boot? Do I need to boot gem5 to use script file? Best regards, Jung Min You 2018-06-08 16:43 GMT+09:00 조해윤 <chohy2...@gmail.com>: > Dear Jung Min You. > > It is strange. Is it booted well? > > What the terminal you mean? > Is it terminal of telnet? Or is it terminal which you typed command line? > > The file, system.terminal, is the same result of the telnet terminal. > > Best regards, > > Haeyoon Cho. > > 2018-06-08 16:18 GMT+09:00 류정민 <jungmin.yo...@gmail.com>: > >> Dear Haeyoon Cho, >> >> I changed script file and run the simulation again. >> >> the script file as follows >> >> >> >> # !/bin/sh >> echo "let's start benchmark simulation" >> >> cd /parsec/parsec/install/bin >> >> /parsec/sbin/m5 dumpstats >> /parsec/sbin/m5 resetstats >> >> ./blackscholes 64 /parsec/parsec/install/inputs/blackscholes/in_16K.txt >> /parsec/parsec/install/inputs/blackscholes/prices.txt >> >> echo "finish! :D" >> >> /parsec/sbin/m5 exit >> /parsec/sbin/m5 exit >> >> >> >> >> Same as the previous case, the echo statements didn't print on the >> terminal. >> >> As the echo statement located at the first line, I think it must be >> printed. >> >> Thanks. >> >> Best regards, >> >> Jung Min. >> >> >> 2018-06-08 15:50 GMT+09:00 조해윤 <chohy2...@gmail.com>: >> >>> Dear Jung Min You. >>> >>> The command line looks fine. >>> >>> How did you write the script? >>> The hack_back_ckpt.rcS is basically for checkpoint. >>> This script detect itself whether is was run before, in other words, the >>> simulation was restored by the checkpoint. >>> Thus, depend on the position of the echo command in your script, it may >>> not run. >>> >>> Best regards, >>> >>> Haeyoon Cho. >>> >>> 2018-06-08 11:41 GMT+09:00 류정민 <jungmin.yo...@gmail.com>: >>> >>>> Hi, >>>> >>>> my name is Jung Min You and I'm graduated course student in >>>> Sungkyunkwan University, South Korea. >>>> >>>> I followed your tutorial to study about gem5. >>>> >>>> For my research, I need to simulate the system using a gem5 full system >>>> mode. >>>> >>>> When I tried to run the fs mode, I used the script files located in >>>> gem5/configs/boot/~~.rcS. >>>> >>>> Meanwhile, to debug the result, I inserted some echo statement in the >>>> script file. >>>> >>>> However, no debug statement has printed in terminal. >>>> >>>> I tried to use hack_back_ckpt.rcS, and my command line as follows. >>>> >>>> build/X86/gem5.opt configs/example/fs.py --cpu-type="AtomicSimpleCPU" >>>> --caches --l1i_size=32kB --l1d_size=32kB - -l2_size=2MB -F 200000000 -I >>>> 200000000 --kernel=$GEM5_DIR/system/binaries/x86_64-vmlinux-2.6.22.9.smp >>>> --disk-image=$GEM5_DIR /system/disks/linux-x86.img >>>> --script=configs/boot/hack_back_ckpt.rcS >>>> >>>> If there is any mistakes in my simulation progress, please tell me what >>>> is the problem. >>>> >>>> Best regards, >>>> >>>> Jung Min. >>>> >>>> >>>> _______________________________________________ >>>> gem5-users mailing list >>>> gem5-users@gem5.org >>>> http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users >>>> >>> >>> >>> _______________________________________________ >>> gem5-users mailing list >>> gem5-users@gem5.org >>> http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users >>> >> >> >> _______________________________________________ >> gem5-users mailing list >> gem5-users@gem5.org >> http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users >> > > > _______________________________________________ > gem5-users mailing list > gem5-users@gem5.org > http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users >
_______________________________________________ gem5-users mailing list gem5-users@gem5.org http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users