I think you can only use one type of memory. Memory hash interleaving is mostly for channel selection.
Hassan On Wed, 20 Mar 2019, 13:41 Qureshi Yasir Mahmood, <[email protected]> wrote: > Hi, > > > > I am trying to use multiple channels in an ARM FS simulation with both > DDR4 and HBM memory models. I use --mem-channels=8 and --mem-size=4GB > options to configure the memory size and number of channels. > > > > In config.ini I do see 8 memory controllers being initialized (0 to 7), > but the memory traffic always goes to just one memory controller, i.e. > mem_ctrls7. > > > > I enabled the *AddrRanges* debug flag, and it shows that the ranges were > allocated correctly > > > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [22 : 19] = 0 for id 6 > > 0: system.membus: Received range change from slave port > system.mem_ctrls1.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 1 for id 7 > > 0: system.membus: Received range change from slave port > system.mem_ctrls2.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 2 for id 8 > > 0: system.membus: Received range change from slave port > system.mem_ctrls3.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 3 for id 9 > > 0: system.membus: Received range change from slave port > system.mem_ctrls4.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 4 for id 10 > > 0: system.membus: Received range change from slave port > system.mem_ctrls5.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 5 for id 11 > > 0: system.membus: Received range change from slave port > system.mem_ctrls6.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 6 for id 12 > > 0: system.membus: Received range change from slave port > system.mem_ctrls7.port > > 0: system.membus: Adding range [0x80000000 : 0x17fffffff], [9 : 7] > XOR [21 : 19] = 7 for id 13 > > . > > . > > . > > 0: system.membus: -- Merging range from 8 ranges > > 0: system.membus: -- Adding merged range [0x80000000 : 0x17fffffff] > > > > I have tried to turn off the XOR hashed interleaving, but it did not help > either. I have used both STREAM and also mmap on /dev/mem to allocate > memory on selected physical addresses, to be sure what address I am > accessing, but the accesses always end up in mem_ctrls7. > > > > Can anyone help identify where the problem is ? Is it a problem in the > coherent Xbar, which is the being used as the system bus ? > > > > Regards > > Yasir > > > > > _______________________________________________ > gem5-users mailing list > [email protected] > http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users
_______________________________________________ gem5-users mailing list [email protected] http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users
