Hello, Thank you for your reply. I was simply following the documentation on the gem5 website: https://www.gem5.org/documentation/general_docs/gpu_models/GCN3 In other words, to build the image, I used: docker build -t gcn-gpu .
This command didn't complete and was interrupted by the error I pasted in the previous mail. I was also using the command in the documentation to compile square: docker run --rm -v $PWD/gem5-resources:$PWD/gem5-resources -w $PWD/gem5-resources/src/gpu/square gcr.io/gem5-test/gcn-gpu make square NOT "make gfx8-apu", as written in the documentation, which caused an error: "no rule to make target 'gfx8-apu' ", and I assumed was a typo. To run it, I also used the command in the doc: docker run --rm -v $PWD/gem5:/gem5 -v $PWD/gem5-resources:/gem5-resources \ -w /gem5 gcr.io/gem5-test/gcn-gpu \ build/GCN3_X86/gem5.opt configs/example/apu_se.py -n2 \ --benchmark-root=/gem5-resources/src/gpu/square/bin \ -c square Note that in these commands, I modified the path of square to 'gem5-resources/src/gpu/square' instead of 'gem5-resources/src/square', because that's where I found the code for it. Also note that I tried downloading the pre-built binary of square (from the gem5-resources website: http://resources.gem5.org/README), but the result was the same: application running indefinitely. Thanks again for your help, Imad PS: If it helps, here are the last things printed when running square in gem5 in the pre-built docker image: [...] just warnings gem5 Simulator System. http://gem5.org gem5 is copyrighted software; use the --copyright option for details. gem5 version 21.1.0.1 gem5 compiled Sep 21 2021 14:52:55 gem5 started Sep 22 2021 15:26:26 gem5 executing on 8d532399b09e, pid 1 command line: build/GCN3_X86/gem5.opt configs/example/apu_se.py -n2 --benchmark-root=/gem5-resources/src/gpu/square/bin -c square info: Standard input is not a terminal, disabling listeners. Num SQC = 1 Num scalar caches = 1 Num CU = 4 coalescer.slave is deprecated. `slave` is now called `in_ports` warn: coalescer.slave is deprecated. `slave` is now called `in_ports` warn: coalescer.slave is deprecated. `slave` is now called `in_ports` [...] same warning as the one right above this line, repeated multiple times warn: system.ruby.network adopting orphan SimObject param 'ext_links' warn: system.ruby.network adopting orphan SimObject param 'int_links' build/GCN3_X86/sim/simulate.cc:107: info: Entering event queue @ 0. Starting simulation... build/GCN3_X86/mem/ruby/system/Sequencer.cc:573: warn: Replacement policy updates recently became the responsibility of SLICC state machines. Make sure to setMRU() near callbacks in .sm files! build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall access(...) build/GCN3_X86/sim/mem_state.cc:443: info: Increasing stack size by one page. build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) [...] same warning as above repeated multiple times build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall set_robust_list(...) build/GCN3_X86/sim/syscall_emul.cc:84: warn: ignoring syscall rt_sigaction(...) (further warnings will be suppressed) build/GCN3_X86/sim/syscall_emul.cc:84: warn: ignoring syscall rt_sigprocmask(...) (further warnings will be suppressed) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall get_mempolicy(...) build/GCN3_X86/arch/generic/debugfaults.hh:144: warn: MOVNTDQ: Ignoring non-temporal hint, modeling as cacheable! build/GCN3_X86/arch/x86/generated/exec-ns.cc.inc:27: warn: instruction 'frndint' unimplemented build/GCN3_X86/sim/mem_state.cc:443: info: Increasing stack size by one page. build/GCN3_X86/gpu-compute/gpu_compute_driver.cc:699: warn: unimplemented ioctl: AMDKFD_IOC_ACQUIRE_VM build/GCN3_X86/sim/syscall_emul.hh:1676: warn: mmap: writing to shared mmap region is currently unsupported. The write succeeds on the target, but it will not be propagated to the host or shared mappings build/GCN3_X86/sim/mem_state.cc:443: info: Increasing stack size by one page. build/GCN3_X86/gpu-compute/gpu_compute_driver.cc:450: warn: Signal events are only supported currently build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/sim/power_state.cc:105: warn: PowerState: Already in the requested power state, request ignored build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall set_robust_list(...) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/gpu-compute/gpu_compute_driver.cc:594: warn: unimplemented ioctl: AMDKFD_IOC_SET_SCRATCH_BACKING_VA build/GCN3_X86/gpu-compute/gpu_compute_driver.cc:604: warn: unimplemented ioctl: AMDKFD_IOC_SET_TRAP_HANDLER info: running on device info: architecture on AMD GPU device is: 801 info: allocate host and device mem ( 7.63 MB) info: launch 'vector_square' kernel build/GCN3_X86/sim/syscall_emul.cc:84: warn: ignoring syscall sched_yield(...) (further warnings will be suppressed) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) build/GCN3_X86/sim/syscall_emul.cc:73: warn: ignoring syscall mprotect(...) On Sep 22 2021, at 5:17 pm, Matt Sinclair <sincl...@cs.wisc.edu> wrote: > Hi Imad, > > I just built the docker earlier this week and did not have any problems > (e.g., I ran square and it completed in < 2 hours). How are you trying to > build it? And how are you running the applications you mentioned? > > Thanks, > Matt > > > > On Wed, Sep 22, 2021 at 12:31 AM Imad Al Assir via gem5-users > <gem5-users@gem5.org (mailto:gem5-users@gem5.org)> wrote: > > Hello, > > Is there a problem with the most recent gcn-gpu docker file? > > I tried building it several times on Ubuntu 20.04 and 18.04 but it kept > > giving me this error: > > > > [...] > > Unpacking rocblas (2.32.0-cc18d25f) ... > > dpkg: dependency problems prevent configuration of rocblas: > > rocblas depends on rocm-core; however: > > Package rocm-core is not installed. > > > > dpkg: error processing package rocblas (--install): > > dependency problems - leaving unconfigured > > dpkg: dependency problems prevent configuration of rocblas-dev: > > rocblas-dev depends on rocblas (>= 2.32.0); however: > > Package rocblas is not configured yet. > > > > dpkg: error processing package rocblas-dev (--install): > > dependency problems - leaving unconfigured > > Errors were encountered while processing: > > rocblas > > rocblas-dev > > + check_exit_code 1 > > + (( 1 != 0 )) > > + exit 1 > > The command '/bin/sh -c ./install.sh -d -a all -i' returned a non-zero > > code: 1 > > > > I also tried downloading the pre-built docker image > > (gcr.io/gem5-test/gcn-gpu (http://gcr.io/gem5-test/gcn-gpu)) and built gem5 > > supposedly with no errors (but with a warning about deprecated namespaces > > not being supported by the compiler). Then when I tried running the > > 'square' sample application and other ones from > > gem5-resources/src/gpu/hip-samples (e.g. MatrixTranspose, dynamic_shared, > > inline_asm, etc.), they just kept running indefinitely (> 2 hours), and I > > had to kill them to stop them. > > May you please try building the latest version of the gcn-gpu dockerfile > > and/or running a sample application on the pre-built docker image, and > > inform us if it works, and if not, how to fix the problem? > > Thanks in advance, > > Imad Al Assir > > _______________________________________________ > > gem5-users mailing list -- gem5-users@gem5.org (mailto:gem5-users@gem5.org) > > To unsubscribe send an email to gem5-users-le...@gem5.org > > (mailto:gem5-users-le...@gem5.org) > > %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s > >
_______________________________________________ gem5-users mailing list -- gem5-users@gem5.org To unsubscribe send an email to gem5-users-le...@gem5.org %(web_page_url)slistinfo%(cgiext)s/%(_internal_name)s