Hi, There are no such line (the one near j.exe) in c:\j601\profile.ijs.
The last block is :
NB. =========================================================
NB. boot up J:
NB. note: this may load a command line script, and should be
NB. the last entry in this script. Any additions beyond this
NB. point may confuse things and cause failures.
0!:0 <jhostpath sys, '\extras\util\boot.ijs'
I put the line just in front No SUCCESS, after the block NO SUCCESS.
----- Original Message -----
From: "Oleg Kobchenko" <[EMAIL PROTECTED]>
To: "General forum" <[email protected]>
Sent: Thursday, June 22, 2006 12:45 PM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
The thing is, Startup script runs before
the session manager is shown. Verify by placing
wd 'Hello' there.
Try putting your kernel... line as the last line of
profile.ijs (the one near j.exe).
----- Original Message ----
From: Claude Bélanger <[EMAIL PROTECTED]>
To: General forum <[email protected]>
Sent: Thursday, June 22, 2006 12:31:04 PM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
Hi,
I made a check by opening J and executing the test and got a crash.
Next, I made a second check by reopening J. Then I used
Edit|Configure|Startup|Open and copied the sentence «kernel32 ...» to the J
screen, executed the sentence got the boxed zeros and no crash on the test.
Please advise.
----- Original Message -----
From: "Eric Iverson" <[EMAIL PROTECTED]>
To: "General forum" <[email protected]>
Sent: Wednesday, June 21, 2006 7:46 PM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
Please check with edit configure to be sure you added the line correctly.
Output from running a script is not normally displayed so don't expect to
see the boxed 0s.
----- Original Message -----
From: "Claude Bélanger" <[EMAIL PROTECTED]>
To: "General forum" <[email protected]>
Sent: Wednesday, June 21, 2006 7:38 PM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
Hello!
I tried to Edit|Configure|Startup, got the message that it didn't exits,
said yes to create it, saved the file and closed J, then restarted J. Got
a clean screen (not even the two boxed zeros). Tried the test and
obviously it didn't took effect because I got the same message.
What did I do wrong?
----- Original Message -----
From: "Eric Iverson" <[EMAIL PROTECTED]>
To: "General forum" <[email protected]>
Sent: Wednesday, June 21, 2006 2:51 PM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
Glad it worked and happy birthday.
Add that sentence to your startup script.
start J
Edit|Configure|Startup
press open to edit the startup.ijs script and add the required line
Could you please do one more experiment for me before you start living
with the workaround. It would narrow down the area where the problem
occurs and might suggest a better solution. There are two chunks of code
that might be causing the problem on your machine. The 1st is the
general startup of the front end and the 2nd is the load of the profile
scripts. I would like you to start J without the startup scripts and try
your test.
Start a Command Prompt window (DOS) (same as you did to test
jconsole.exe)
...>\j601\j.exe -jprofile
this starts a barebones J without loading the profile
%0 1 2 3
does this work or fail?
You need to terminate this J session with the following sentence:
2!:55[0
Bear in mind some of the comments Oleg made. J has run on many systems
and, other than the variation reported by Bill and known problems with
some dll calls, we dont' see this problem. There is something wrong with
your system in some deep dark corner. You can probably ignore it, but
don't forget it.
If this problem were more widely reported we would dig much deeper into
finding a solution.
----- Original Message -----
From: "Claude Bélanger" <[EMAIL PROTECTED]>
To: "general - J Software" <[email protected]>
Sent: Wednesday, June 21, 2006 1:06 PM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
Hi,
It is 13:06, and ALL IS FINE UNDER THE SUN.
From what I tested it seems that I must execute that command everytime
I
open J (win). I remember that there is a file where I should put that
command. Could you tell me wich file. I am relearning at 64( today),
nice birthday gift.
Thanks to everyone who contributed.
Claude Bélanger [EMAIL PROTECTED]
----- Original Message -----
From: "Eric Iverson" <[EMAIL PROTECTED]>
To: "General forum" <[email protected]>
Sent: Wednesday, June 21, 2006 11:25 AM
Subject: Re: [Jgeneral] Crash on % 0 1 2 3
A wild guess is that some action is damaging the floating point state.
Some
dll calls damage the state and require a reset in order for the J
Engine to
continue running properly. For this reason the % option was added to
the cd
mechanism. Please do the following test:
start J
run sentence:
'kernel32 CloseHandle % i i' 15!:0 [0
the result is two boxed zeros
now try your troubling sentence:
%0 1 2 3
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
----------------------------------------------------------------------
For information about J forums see http://www.jsoftware.com/forums.htm
