This conf file is not used any more and should be removed Signed-off-by: Yevgeny Kliteynik <[EMAIL PROTECTED]> --- opensm/scripts/opensm.conf | 137 -------------------------------------------- 1 files changed, 0 insertions(+), 137 deletions(-) delete mode 100644 opensm/scripts/opensm.conf
diff --git a/opensm/scripts/opensm.conf b/opensm/scripts/opensm.conf deleted file mode 100644 index 502eea2..0000000 --- a/opensm/scripts/opensm.conf +++ /dev/null @@ -1,137 +0,0 @@ -# DEBUG mode -# This option specifies a debug option. -# These options are not normally needed. -# The number following -d selects the debug -# option to enable as follows: -# OPT Description -# --- ----------------- -# 0 - Ignore other SM nodes. -# 1 - Force single threaded dispatching. -# 2 - Force log flushing after each log message. -# 3 - Disable multicast support. -# 4 - Put OpenSM in memory tracking mode. -# 10.. Put OpenSM in testability mode. -# none, no debug options are enabled. -DEBUG=none - -# LMC -# This option specifies the subnet's LMC value. -# The number of LIDs assigned to each port is 2^LMC. -# The LMC value must be in the range 0-7. -# LMC values > 0 allow multiple paths between ports. -# LMC values > 0 should only be used if the subnet -# topology actually provides multiple paths between -# ports, i.e. multiple interconnects between switches. -# OpenSM defaults to LMC = 0, which allows -# one path between any two ports. -LMC=0 - -# MAXSMPS -# This option specifies the number of VL15 SMP MADs -# allowed on the wire at any one time. -# Specifying -maxsmps 0 allows unlimited outstanding SMPs. -# Without -maxsmps, OpenSM defaults to a maximum of -# four outstanding SMP. -MAXSMPS=4 - -# REASSIGN_LIDS -# This option causes OpenSM to reassign LIDs to all -# end nodes. Specifying "REASSIGN_LIDS=yes" on a running subnet -# may disrupt subnet traffic. -# With "REASSIGN_LIDS=no", OpenSM attempts to preserve existing -# LID assignments resolving multiple use of same LID. -REASSIGN_LIDS="no" - -# SWEEP -# This option specifies the number of seconds between -# subnet sweeps. Specifying SWEEP=0 disables sweeping. -# OpenSM defaults to a sweep interval of 10 seconds. -SWEEP=10 - -# TIMEOUT -# This option specifies the time in milliseconds -# used for transaction timeouts. -# Specifying -t 0 disables timeouts. -# Without -t, OpenSM defaults to a timeout value of -# 200 milliseconds. -TIMEOUT=200 - -# OSM_LOG -# This option defines the log to be the given file. -# By default the log goes to /var/log/opensm.log -# For the log to go to standard output use OSM_LOG=stdout. -OSM_LOG=/var/log/opensm.log - -# VERBOSE -# This option increases the log verbosity level. -# The "-v" option may be specified multiple times -# to further increase the verbosity level. -# "-V" option sets the maximum verbosity level and -# forces log flushing. -# The "-V" is equivalent to "-vf 0xFF -d 2". -VERBOSE="none" - -# UPDN -# This option activate UPDN algorithm instead of Min Hop -# algorithm (default). -# To switch on UPDN algorithm set UPDN="on" -UPDN="off" - -# GUID_FILE -# This option only allowed when UPDN algorithm is activated -# It specifies the guid list file from which to fetch the guid list -# The file contain in each line only one valid guid -GUID_FILE="none" - -# This option specifies the local port GUID value -# with which OpenSM should bind. OpenSM may be -# bound to 1 port at a time. -# If GUID given is 0, opensmd use PORT_NUM parameter. -# Without -g (GUID="none"), OpenSM trys to use the default port. -GUID=0 - -# OSM_HOSTS -# The list of all SM's IP addresses in InfiniBand subnet -# Used to handover mechanism -OSM_HOSTS="" - -# OSM_CACHE_DIR -OSM_CACHE_DIR=/var/cache/opensm - -# CACHE_OPTIONS -# Cache the given command line options into the file -# OSM_CACHE_DIR/opensm.opts for use next invocation -# Set to '--cache-options' or '-c' in order to enable -CACHE_OPTIONS="none" - -# HONORE_GUID2LID -# This option forces OpenSM to honor the guid2lid file, -# when it comes out of Standby state, if such file exists -# under OSM_CACHE_DIR, and is valid. -# Set to '--honor_guid2lid' or '-x' to enable. -# By default this is FALSE. Will be set automatically to '--honor_guid2lid' -# if OSM_HOSTS includes list of more then one IP addresses. -HONORE_GUID2LID="none" - -# RCP -# This option osed by SLDD daemon for handover mechanism -# to copy local cache file to remote computer -RCP=/usr/bin/scp - -# RSH -# This option osed by SLDD daemon for handover mechanism -# to execute commands on remote computer -RSH=/usr/bin/ssh - -# RESCAN_TIME -# This option osed by SLDD daemon for handover mechanism -# Time between sweep of sldd daemon in seconds -RESCAN_TIME=60 - -# PORT_NUM -# This option defines HCA's port number which OpenSM should bind -PORT_NUM=1 - -# ONBOOT -# To start OpenSM automatically set ONBOOT=yes -ONBOOT=no -- 1.5.1.4 _______________________________________________ general mailing list general@lists.openfabrics.org http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
