Tziporet, I get two x4600 and think they are same, but on the one failed to startup when I run mstflint: mstflint -d 03:00.0 q Warning: memory access to device 03:00.0 failed: Input/output error. Warning: Fallback on IO: much slower, and unsafe if device in use. *** ERROR *** Can not open 03:00.0: Not a directory MFE_CR_ERROR
On the other one (which load driver without error): mstflint -d 03:00.0 q Image type: Failsafe I.S. Version: 1 Chip Revision: A0 Description: Node Port1 Port2 Sys image GUIDs: 00066a0098006abd 00066a00a0006abd 00066a01a0006abd 00066a0098006abd Board ID: j (MT_00A0000001) VSD: j PSID: MT_00A0000001 mstflint -d 03:00.0 v Failsafe image: Invariant /0x00000028-0x0000095f (0x000938)/ (BOOT2) - OK Primary Image /0x00010000-0x00010107 (0x000108)/ (Pointer Sector)- OK /0x00030028-0x000308af (0x000888)/ (BOOT2) - OK /0x000308b0-0x00034feb (0x00473c)/ (BOOT2) - OK /0x00034fec-0x00035edb (0x000ef0)/ (Configuration) - OK /0x00035edc-0x00035f0f (0x000034)/ (GUID) - OK /0x00035f10-0x0003ed63 (0x008e54)/ (DDR) - OK /0x0003ed64-0x0004d63b (0x00e8d8)/ (DDR) - OK /0x0004d63c-0x00050573 (0x002f38)/ (DDR) - OK /0x00050574-0x0005204f (0x001adc)/ (DDR) - OK /0x00052050-0x0006accf (0x018c80)/ (DDR) - OK /0x0006acd0-0x0007f23f (0x014570)/ (DDR) - OK /0x0007f240-0x0007f253 (0x000014)/ (Configuration) - OK /0x0007f254-0x0007f297 (0x000044)/ (Jump addresses) - OK /0x0007f298-0x0007f33f (0x0000a8)/ (FW Configuration) - OK Secondary Image /0x00020000-0x00020107 (0x000108)/ (Pointer Sector)- OK /0x00080028-0x000808af (0x000888)/ (BOOT2) - OK /0x000808b0-0x00084feb (0x00473c)/ (BOOT2) - OK /0x00084fec-0x00085edb (0x000ef0)/ (Configuration) - OK /0x00085edc-0x00085f0f (0x000034)/ (GUID) - OK /0x00085f10-0x0008ed63 (0x008e54)/ (DDR) - OK /0x0008ed64-0x0009d63b (0x00e8d8)/ (DDR) - OK /0x0009d63c-0x000a0573 (0x002f38)/ (DDR) - OK /0x000a0574-0x000a204f (0x001adc)/ (DDR) - OK /0x000a2050-0x000baccf (0x018c80)/ (DDR) - OK /0x000bacd0-0x000cf23f (0x014570)/ (DDR) - OK /0x000cf240-0x000cf253 (0x000014)/ (Configuration) - OK /0x000cf254-0x000cf297 (0x000044)/ (Jump addresses) - OK /0x000cf298-0x000cf33f (0x0000a8)/ (FW Configuration) - OK FW image verification succeeded. Image is bootable. Thanks Liang Tziporet Koren wrote: > Liang Zhen wrote: > >> Hi Ole, >> Have you got solution for this? I think we got exactly same problem on >> 4600 with ofed-1.4.1-rc4: >> lspci output: >> 03:00.0 InfiniBand: Mellanox Technologies MT25418 [ConnectX IB DDR, PCIe >> 2.0 2.5GT/s] (rev a0) >> >> and error messages from dmesg: >> >> mlx4_core: Mellanox ConnectX core driver v1.0 (April 4, 2008) >> mlx4_core: Initializing 0000:03:00.0 >> mlx4_core 0000:03:00.0: Requested number of MACs is too much for port 1, >> reducing to 1. >> mlx4_core 0000:03:00.0: command 0x13 failed: fw status = 0x1 >> mlx4_core 0000:03:00.0: SW2HW_EQ failed (-5) >> mlx4_core 0000:03:00.0: Failed to initialize event queue table, aborting. >> mlx4_core: probe of 0000:03:00.0 failed with error -5 >> >> >> > Can you send me the FW version and board type > Since the driver is not loading you can use mstflint to get this data > Please use: > > The devices can be accessed by their PCI ID as displayed by lspci > (bus:dev.fn). > Example: > # List all Mellanox devices > >> /sbin/lspci -d 15b3: >> > 02:00.0 Ethernet controller: Mellanox Technologies Unknown device 6368 > (rev a0) > > # Use mstflint tool to query the firmware on this device > >> mstflint -d 02:00.0 q >> > > Tziporet > _______________________________________________ > general mailing list > [email protected] > http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general > > To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general > _______________________________________________ general mailing list [email protected] http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
