On 7/5/06, A. R. <[EMAIL PROTECTED]> wrote:
Okay, I emerged ndiswrapper which also emerged wireless-tools. I haven't yet created any configuration files. However, if I run iwconfig, this is what I get:
localhost ~ # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:"beam26wireless"
Mode:Managed Frequency:2.437 GHz Access Point: 00:13:10:99:9C:BF
Bit Rate:54 Mb/s Tx-Power:25 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-60 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
So, I assume that eth1 would be replaced by wlan0 in the commands above, correct?
Well, I already have wireless-tools on my laptop because it was installed with ndiswrapper. As you note, my access point (a wireless cable/DSL router) is recognized and I realize that there isn't an encryption key set.
The thing is, I *have* looked at /etc/conf.d/wireless.example and it may as well be hieroglyphics. I don't know which section to alter. Right now, if I'm on my laptop, I want to be able to connect to the access point in my apartment. However, if I'm at someplace that has wireless access, I want to be able to scan for an available network. So, I don't know what section to changed.
I'm just a user and not a network person, so further help would be appreciated.
Regards,
Colleen
> So, my question is, once I install ndiswrapper and the driver, do I then
> follow the wiki for either wireless-tools or (preferred)
> wpa-supplicant? Is there anything else I have to do or install?
>
> Regards,
>
> Colleen
>
Hello,
May I suggest that you try first with wireless-tools?
Things you need to know:
1. The interface id of the wireless card (eth0, eth1, wlan0 etc...)
2. The "essid" of the wireless access point you are connecting to.
3. The encryption key (if any) for wireless access (WEP)
Once you have those you can run the following commands (after you have
emerged wireless-tools) Using eth1 as the interface for example:
iwconfig eth1 essid <the essid of the access point>
iwconfig eth1 key <the encryption key>
dhcpcd eth1
Okay, I emerged ndiswrapper which also emerged wireless-tools. I haven't yet created any configuration files. However, if I run iwconfig, this is what I get:
localhost ~ # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:"beam26wireless"
Mode:Managed Frequency:2.437 GHz Access Point: 00:13:10:99:9C:BF
Bit Rate:54 Mb/s Tx-Power:25 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-60 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
So, I assume that eth1 would be replaced by wlan0 in the commands above, correct?
If this works, then depending on how you want to configure your box
you may want to set all this configuration in the file
/etc/conf.d/wireless (BTW, please take a look at the file
/etc/conf.d/wireless.example, it does have very good comments that
would make this very understandable), or you may want to go for
wpa_supplicant.
Well, I already have wireless-tools on my laptop because it was installed with ndiswrapper. As you note, my access point (a wireless cable/DSL router) is recognized and I realize that there isn't an encryption key set.
The thing is, I *have* looked at /etc/conf.d/wireless.example and it may as well be hieroglyphics. I don't know which section to alter. Right now, if I'm on my laptop, I want to be able to connect to the access point in my apartment. However, if I'm at someplace that has wireless access, I want to be able to scan for an available network. So, I don't know what section to changed.
I'm just a user and not a network person, so further help would be appreciated.
Regards,
Colleen
