On Sun, Sep 27, 2009 at 08:15:46AM -0700, walt wrote
> I'm using the vbox svn repository from Sun, so I haven't tried building
> the portage version.
As I mentioned, I'm using Sun's install because the portage install
dies.
> What problem do you see?
At bootup I get...
* Starting VirtualBox kernel module ...
* modprobe vboxdrv failed. Please use 'dmesg' to find out why
I'm attaching dmesg output in the hope that someone can figure this
out.
--
Walter Dnes <waltd...@waltdnes.org>
Linux version 2.6.29-gentoo-r5 (r...@d530) (gcc version 4.3.2 (Gentoo 4.3.2-r3
p1.6, pie-10.1.5) ) #1 SMP Fri Jul 10 23:46:49 EDT 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000099c00 (usable)
BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f590000 (usable)
BIOS-e820: 000000007f590000 - 000000007f5e3000 (ACPI NVS)
BIOS-e820: 000000007f5e3000 - 000000007f5f0000 (ACPI data)
BIOS-e820: 000000007f5f0000 - 000000007f600000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.5 present.
last_pfn = 0x7f590 max_arch_pfn = 0x100000
kernel direct mapping tables up to 377fe000 @ 7000-c000
ACPI: RSDP 000F96C0, 0024 (r2 DELL )
ACPI: XSDT 7F5E3080, 005C (r1 DELL FX09 42302E31 AWRD 0)
ACPI: FACP 7F5E7200, 00F4 (r3 DELL FX09 42302E31 AWRD 0)
ACPI Warning (tbfadt-0568): 32/64X length mismatch in Pm1aEventBlock: 32/8
[20081204]
ACPI Warning (tbfadt-0568): 32/64X length mismatch in Pm1aControlBlock: 16/8
[20081204]
ACPI Warning (tbfadt-0568): 32/64X length mismatch in PmTimerBlock: 32/8
[20081204]
ACPI Warning (tbfadt-0568): 32/64X length mismatch in Gpe0Block: 128/8
[20081204]
ACPI Warning (tbfadt-0412): Invalid length for Pm1aEventBlock: 8, using default
32 [20081204]
ACPI Warning (tbfadt-0412): Invalid length for Pm1aControlBlock: 8, using
default 16 [20081204]
ACPI Warning (tbfadt-0412): Invalid length for PmTimerBlock: 8, using default
32 [20081204]
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT 7F5E3200, 3FFC (r1 DELL AWRDACPI 1000 MSFT 3000000)
ACPI: FACS 7F590000, 0040
ACPI: HPET 7F5E73C0, 0038 (r1 DELL FX09 42302E31 AWRD 98)
ACPI: MCFG 7F5E7400, 003C (r1 DELL FX09 42302E31 AWRD 0)
ACPI: SLIC 7F5E7440, 0176 (r1 DELL FX09 42302E31 AWRD 0)
ACPI: DMY2 7F5E75C0, 0080 (r1 DELL FX09 42302E31 AWRD 0)
ACPI: APIC 7F5E7300, 0084 (r1 DELL FX09 42302E31 AWRD 0)
ACPI: SSDT 7F5E7CA0, 0380 (r1 PmRef CpuPm 3000 INTL 20041203)
ACPI: Local APIC address 0xfee00000
1149MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 00000000 - 377fe000
bootmap 00008000 - 0000ef00
(8 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 0000705d54] TEXT DATA BSS ==> [0000100000 - 0000705d54]
#4 [0000706000 - 0000709000] INIT_PG_TABLE ==> [0000706000 - 0000709000]
#5 [0000099c00 - 0000100000] BIOS reserved ==> [0000099c00 - 0000100000]
#6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#7 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
found SMP MP-table at [c00f3e30] 000f3e30
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007f590
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00000099
0: 0x00000100 -> 0x0007f590
On node 0 totalpages: 521513
free_area_init_node: node 0, pgdat c06264c0, node_mem_map c1000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3961 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2300 pages used for memmap
HighMem zone: 291990 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
4 Processors exceeds NR_CPUS limit of 2
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 0000000000099000 - 000000000009a000
PM: Registered nosave memory: 000000000009a000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7f600000:60a00000)
NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Allocating 32768 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517437
Kernel command line: BOOT_IMAGE=Production ro root=805 nofirewire noexec=on
noexec32=on
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 1596.088 MHz processor.
Console: colour VGA+ 80x60
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2061788k/2086464k available (3918k kernel code, 23432k reserved, 1452k
data, 320k init, 1177160k highmem)
virtual kernel memory layout:
fixmap : 0xfff9f000 - 0xfffff000 ( 384 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc0646000 - 0xc0696000 ( 320 kB)
.data : 0xc04d389b - 0xc063ec08 (1452 kB)
.text : 0xc0100000 - 0xc04d389b (3918 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
hpet clockevent registered
HPET: 4 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency..
3192.17 BogoMIPS (lpj=6384352)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20081204
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Genuine Intel(R) CPU 2140 @ 1.60GHz stepping 02
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3192.00 BogoMIPS (lpj=6384018)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Genuine Intel(R) CPU 2140 @ 1.60GHz stepping 02
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6384.18 BogoMIPS).
net_namespace: 504 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: reg 10 32bit mmio: [0xfdf00000-0xfdf7ffff]
pci 0000:00:02.0: reg 14 io port: [0xff00-0xff07]
pci 0000:00:02.0: reg 18 32bit mmio: [0xc0000000-0xcfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xfdd00000-0xfddfffff]
pci 0000:00:19.0: reg 10 32bit mmio: [0xfdfc0000-0xfdfdffff]
pci 0000:00:19.0: reg 14 32bit mmio: [0xfdfff000-0xfdffffff]
pci 0000:00:19.0: reg 18 io port: [0xfe00-0xfe1f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0xfd00-0xfd1f]
pci 0000:00:1a.1: reg 20 io port: [0xfc00-0xfc1f]
pci 0000:00:1a.2: reg 20 io port: [0xfb00-0xfb1f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfdffe000-0xfdffe3ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfdff4000-0xfdff7fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xfa00-0xfa1f]
pci 0000:00:1d.1: reg 20 io port: [0xf900-0xf91f]
pci 0000:00:1d.2: reg 20 io port: [0xf800-0xf81f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfdffd000-0xfdffd3ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 003f)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 003f)
pci 0000:00:1f.2: reg 10 io port: [0xf700-0xf707]
pci 0000:00:1f.2: reg 14 io port: [0xf600-0xf603]
pci 0000:00:1f.2: reg 18 io port: [0xf500-0xf507]
pci 0000:00:1f.2: reg 1c io port: [0xf400-0xf403]
pci 0000:00:1f.2: reg 20 io port: [0xf300-0xf31f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfdffc000-0xfdffc7ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xfdffb000-0xfdffb0ff]
pci 0000:00:1f.3: reg 20 io port: [0x500-0x51f]
pci 0000:00:01.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfdb00000-0xfdbfffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xfdc00000-0xfdcfffff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:02:00.0: reg 14 io port: [0xcc00-0xccff]
pci 0000:02:00.0: reg 18 32bit mmio: [0xfdef0000-0xfdefffff]
pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:02:00.0: supports D1 D2
pci 0000:02:01.0: reg 10 io port: [0xcf00-0xcf07]
pci 0000:02:01.0: supports D2
pci 0000:02:01.0: PME# supported from D0 D2 D3hot D3cold
pci 0000:02:01.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xfde00000-0xfdefffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 *4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *9 10 11 12 14 15)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x800-0x87f has been reserved
system 00:01: ioport range 0x290-0x297 has been reserved
system 00:01: ioport range 0x880-0x88f has been reserved
system 00:08: ioport range 0x400-0x4bf could not be reserved
system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0b: iomem range 0xf0000-0xfffff could not be reserved
system 00:0b: iomem range 0x7f600000-0x7f6fffff has been reserved
system 00:0b: iomem range 0xfed00000-0xfed000ff has been reserved
system 00:0b: iomem range 0x7f590000-0x7f5fffff could not be reserved
system 00:0b: iomem range 0x0-0x9ffff could not be reserved
system 00:0b: iomem range 0x100000-0x7f58ffff could not be reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0b: iomem range 0xfed14000-0xfed1dfff has been reserved
system 00:0b: iomem range 0xfed20000-0xfed9ffff has been reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xffb00000-0xffb7ffff has been reserved
system 00:0b: iomem range 0xfff00000-0xffffffff has been reserved
system 00:0b: iomem range 0xe0000-0xeffff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0xd000-0xdfff
pci 0000:00:01.0: MEM window: 0xfdb00000-0xfdbfffff
pci 0000:00:01.0: PREFETCH window: 0x000000fdc00000-0x000000fdcfffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: 0xc000-0xcfff
pci 0000:00:1e.0: MEM window: 0xfde00000-0xfdefffff
pci 0000:00:1e.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xfdb00000-0xfdbfffff]
pci_bus 0000:01: resource 2 mem: [0xfdc00000-0xfdcfffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 io: [0xc000-0xcfff]
pci_bus 0000:02: resource 1 mem: [0xfde00000-0xfdefffff]
pci_bus 0000:02: resource 2 mem: [0xd0000000-0xdfffffff]
pci_bus 0000:02: resource 3 io: [0x00-0xffff]
pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
kvm: no hardware support
Machine check exception polling timer started.
microcode: no support for this CPU vendor
highmem bounce pool size: 64 pages
NTFS driver 2.1.29 [Flags: R/W].
msgmni has been set to 1729
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pci 0000:02:00.0: Boot video device
Real Time Clock Driver v1.12b
Linux agpgart interface v0.103
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60
seconds).
Hangcheck: Using get_cycles().
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT 7F5E7680, 022A (r1 PmRef Cpu0Ist 3000 INTL 20041203)
processor ACPI_CPU:00: registered as cooling_device0
ACPI: SSDT 7F5E7B40, 0152 (r1 PmRef Cpu1Ist 3000 INTL 20041203)
processor ACPI_CPU:01: registered as cooling_device1
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
serial 0000:02:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
0000:02:01.0: ttyS4 at I/O 0xcf00 (irq = 16) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
brd: module loaded
loop: module loaded
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: setting latency timer to 64
e1000e 0000:00:19.0: irq 24 for MSI/MSI-X
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1a:a0:8c:0d:b2
0000:00:19.0: eth0: Intel(R) PRO/10/100 Network Connection
0000:00:19.0: eth0: MAC: 6, PHY: 7, PBA No: ffffff-0ff
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
console [netcon0] enabled
netconsole: network logging started
Linux video capture interface: v2.00
3ware Storage Controller device driver for Linux v1.26.02.002.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 25 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp pio slum part ems
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2...@0xfdffc000 port 0xfdffc100 irq 25
ata2: SATA max UDMA/133 abar m2...@0xfdffc000 port 0xfdffc180 irq 25
ata3: SATA max UDMA/133 abar m2...@0xfdffc000 port 0xfdffc200 irq 25
ata4: SATA max UDMA/133 abar m2...@0xfdffc000 port 0xfdffc280 irq 25
ata5: SATA max UDMA/133 abar m2...@0xfdffc000 port 0xfdffc300 irq 25
ata6: SATA max UDMA/133 abar m2...@0xfdffc000 port 0xfdffc380 irq 25
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-11, max UDMA7
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: HL-DT-ST CD-RW/DVD-ROM GCC-H10N, C103, max UDMA/100
ata2.00: configured for UDMA/100
scsi 1:0:0:0: CD-ROM HL-DT-ST CDRW/DVD GCCH10N C103 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ATAPI: HL-DT-STDVD+-RW GSA-H31N, B109, max UDMA/100
ata5.00: configured for UDMA/100
scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-H31N B109 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
sr 4:0:0:0: Attached scsi CD-ROM sr1
sr 4:0:0:0: Attached scsi generic sg2 type 5
ata6: SATA link down (SStatus 0 SControl 300)
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdffe000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffd000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000fd00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fb00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fa00
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f900
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f800
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18a.
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
ALSA device list:
#0: HDA Intel at 0xfdff4000 irq 22
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
VFS: Mounted root (ext2 filesystem) readonly on device 8:5.
Freeing unused kernel memory: 320k freed
usb 2-3: new high speed USB device using ehci_hcd and address 2
usb 2-3: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 4-2: new low speed USB device using uhci_hcd and address 2
udev: starting version 141
udev: deprecated sysfs layout; update the kernel or disable
CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
usb 4-2: configuration #1 chosen from 1 choice
input: Dell Dell USB Keyboard as /class/input/input2
generic-usb 0003:413C:2003.0001: input: USB HID v1.10 Keyboard [Dell Dell USB
Keyboard] on usb-0000:00:1a.1-2/input0
usb 5-1: new low speed USB device using uhci_hcd and address 2
usb 5-1: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Trackball as /class/input/input3
generic-usb 0003:046D:C401.0002: input: USB HID v1.00 Mouse [Logitech USB-PS/2
Trackball] on usb-0000:00:1a.2-1/input0
agpgart-intel 0000:00:00.0: Intel G33 Chipset
agpgart-intel 0000:00:00.0: detected 7164K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
pci 0000:02:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
pci 0000:02:00.0: setting latency timer to 64
[drm] Initialized radeon 1.29.0 20080528 on minor 0
scsi 6:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg3 type 0
scsi 6:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
sd 6:0:0:1: [sdc] Attached SCSI removable disk
sd 6:0:0:1: Attached scsi generic sg4 type 0
scsi 6:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
sd 6:0:0:2: [sdd] Attached SCSI removable disk
sd 6:0:0:2: Attached scsi generic sg5 type 0
scsi 6:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
sd 6:0:0:3: [sde] Attached SCSI removable disk
sd 6:0:0:3: Attached scsi generic sg6 type 0
usb-storage: device scan complete
ReiserFS: sda7: found reiserfs format "3.6" with standard journal
ReiserFS: sda7: using ordered data mode
ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda7: checking transaction log (sda7)
ReiserFS: sda7: Using r5 hash to sort names
Adding 3911788k swap on /dev/sda6. Priority:-1 extents:1 across:3911788k
e1000e 0000:00:19.0: irq 24 for MSI/MSI-X
e1000e 0000:00:19.0: irq 24 for MSI/MSI-X
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
0000:00:19.0: eth0: 10/100 speed: disabling TSO
0000:00:19.0: eth0: changing MTU from 1500 to 1454
e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
0000:00:19.0: eth0: 10/100 speed: disabling TSO
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
IN= OUT=lo SRC=127.0.0.2 DST=127.0.0.2 LEN=40 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF
PROTO=TCP SPT=80 DPT=36255 WINDOW=0 RES=0x00 ACK RST URGP=0
IN= OUT=lo SRC=127.0.0.2 DST=127.0.0.2 LEN=40 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF
PROTO=TCP SPT=80 DPT=36255 WINDOW=0 RES=0x00 ACK RST URGP=0
IN= OUT=lo SRC=127.0.0.2 DST=127.0.0.2 LEN=40 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF
PROTO=TCP SPT=80 DPT=36255 WINDOW=0 RES=0x00 ACK RST URGP=0
IN= OUT=lo SRC=127.0.0.2 DST=127.0.0.2 LEN=40 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF
PROTO=TCP SPT=80 DPT=36255 WINDOW=0 RES=0x00 ACK RST URGP=0
IN= OUT=lo SRC=127.0.0.2 DST=127.0.0.2 LEN=40 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF
PROTO=TCP SPT=80 DPT=36255 WINDOW=0 RES=0x00 ACK RST URGP=0
[drm] Loading R200 Microcode
