*NewYork Coverage of this news:*
https://www.nytimes.com/2026/05/14/climate/stardust-solutions-geoengineering-cooling-earth.html?unlocked_article_code=1.iVA.JhtR.MmA4X_lfXHfp&smid=url-share

*14 May 2026*

*Stardust's papers linked below:*
https://stardustsrt.com/science

*Paper#01: From Particles to Policy: Technical Building Blocks for
Multi-State SAI Coordination*
https://stardustsrt.com/science/from-particles-to-policy
*Authors*: Roby Yahav, Amyad Spector, Doron Kushnir, and Matthew C. Waxman
*Abstract*
Stratospheric aerosol injection (SAI) is a solar radiation modification
technique, proposed as an interim measure to offset warming while
greenhouse gas (GHG) emissions are reduced. This paper discusses a possible
SAI implementation route - an alternative to sulfate aerosols formed in
situ - based on engineered solid particles having dedicated properties such
as size, composition, surface chemistry, and traceable origin, supporting
safety, controllability, and functionality needed for SAI systems. These
engineered properties also open up options for any future multi-state
coordination of SAI through two technical building blocks: (1) the
SAI-induced radiative forcing (SRF) - the magnitude of the cooling effect
attributable specifically to the SAI layer - as an operator-independent
quantity, derivable from direct aerosol-layer measurements; and (2)
particle traceability through identifying signatures embedded at
production. Both could feed into a shared, publicly accessible monitoring
database open to independent interrogation, addressing several governance
challenges by anchoring compliance assessments in measurable parameters.
Drawing on precedents from the Montreal Protocol, IAEA safeguards, and
other regimes, we show that shared technical metrics have historically
enabled multi-state cooperation, and we argue the same could apply to SAI.
We describe a phased pathway in which the technical capabilities and
coordination practices that would use them are developed and tested
together, at scales orders of magnitude below operational deployment. To be
clear - we regard SAI deployment as premature; the conditions under which
it might be considered have not been met. The paper does not propose a
governance framework; rather, it identifies technical infrastructure that
could support a wide range of such frameworks.

*Paper#02: Engineered amorphous silica particles with minimized
heterogeneous uptake behavior for stratospheric aerosol injection*
https://stardustsrt.com/science/engineered-amorphous-silica-particles
*Authors*: Tzemah Kislev, Alina Berkman, Gal Schwartz Roitman, Kariene
Neiman, Anais Lostier, Subhadarsi Nayak, Amir Goldbourt, David Avnir,
Manolis N. Romanias
*Abstract*
Solar radiation modification via stratospheric aerosol injection (SAI) has
been proposed as a potential approach to partially offset anthropogenic
climate warming. However, its feasibility is constrained by uncertainties
associated with heterogeneous interactions between aerosol particles and
trace gases relevant to stratospheric ozone chemistry.

Here, we develop and experimentally evaluate engineered amorphous silica
particles designed for SAI-relevant functionality, with particular emphasis
on minimizing heterogeneous uptake behavior under stratospheric conditions.
Controlled synthesis, thermal treatment, and surface functionalization
yield dense, spherical particles with reduced densities of accessible
surface silanol groups, substantial hydrophobic surface functionalization,
and stable hydrophobic characteristics under ultraviolet (UV) irradiation
and exposure to acidic species.

Heterogeneous uptake of key trace gases, including HCl, HNO3, N2O5, and O3,
was measured under low-temperature conditions relevant to the lower
stratosphere. The engineered particles exhibit substantially reduced uptake
compared with crystalline quartz, which is used here as a low-uptake
benchmark surface, with uptake coefficients approaching experimental
detection limits and interactions dominated primarily by weak surface
association.

These findings extend benchmark measurements identifying amorphous silica
as a low-uptake reference material and demonstrate that heterogeneous
uptake behavior can be further suppressed through controlled surface
engineering. The consistently low uptake observed across multiple trace
gases suggests a substantially reduced potential for sustained
heterogeneous gas–surface processing under representative stratospheric
conditions, supporting the potential compatibility of such particles with
ozone-relevant atmospheric chemistry.

*Paper#03: Efficient dispersal of submicron solid particles for
stratospheric aerosol injection*
https://stardustsrt.com/science/efficient-dispersal-of-submicron-solid-particles
*Authors: *Yair Segev, Eitan Y. Levine, Yair Bar-Yoseph, Ori Amsallem,
Yuval Dagan, Elad Laor, Shai Rahamim, Alon Luski, Eran Daniel, Eshani
Hettiarachchi, Amyad Spector
*Abstract*
Stratospheric aerosol injection (SAI) using solid particles has been
proposed as an alternative to sulfate aerosols for solar radiation
modification, but practical deployment faces challenges in efficiently
deagglomerating and dispersing powders as submicron particles. Here we
experimentally demonstrate pneumatic dispersal of particles in optically
optimal size ranges for SAI. Using spherical amorphous silica particles, we
find that applying a hydrophobic surface treatment substantially improves
dispersibility, with 50-85% of treated particle mass achieving submicron
sizes compared to 10% for untreated particles. We compare the dispersal of
treated particles of different sizes and find that 300 nm particles provide
superior deagglomeration than 500 nm particles for the same air
consumption. Theoretical modeling of the adhesion forces between particles,
combined with surface roughness parameters extracted from atomic force
microscopy, successfully predicted the relative dispersibility across
different particle types. The pneumatic dispersal system achieved optimal
performance at air-to-powder mass ratios of about 10:1. Using the measured
dispersed particle sizes, we provide a scaling analysis suggesting that a
feasibly sized fleet of dispersal aircraft could provide an aerosol layer
sufficient for meaningful climate intervention. These results demonstrate
that hydrophobic surface treatment and pneumatic dispersal can overcome the
agglomeration challenge for SAI with solid particles.

*Paper#04: Composite sub-micron solid particles engineered to enable safe,
controllable, efficient, and practical SAI*
https://stardustsrt.com/science/composite-sub-micron-solid-particles
*Authors*: Stardust Labs
*Abstract*
The properties of candidate particles for solar radiation management (SRM)
through stratospheric aerosol injection (SAI) should comply with safety,
controllability, and functionality requirements. Following the proposal in
[1] of safety and controllability requirements, we define here a set of
functionality requirements on the particles’ properties - optical
properties, stratospheric residence time, scalable manufacturing
compatibility, and aerial dispersion compatibility- that, if met, ensure
the feasibility of practical implementation, providing reflection of ∼ 1%
of the solar flux. We then present design principles and fabrication
methods for sub-micron solid particles that may enable satisfying the
combined requirements.

These requirements do not identify a unique solution, but favor sub-micron
particles with tightly controlled size distributions and stable properties
over their stratospheric lifetime, and motivate a composite design where
the bulk core composition is selected primarily for optimal radiative
properties and the outer shell surface is engineered to control atmospheric
chemistry and aging, and enhance aerial dispersion compatibility. We
present two specific particle designs that are viable for meeting the
coupled requirements: amorphous silica spheres and calcium-carbonate cores
surrounded by spherical silica shells (both with appropriate surface
treatment). The former is at an advanced stage of experimental verification
(described in detail in a companion paper) of meeting all requirements,
provides a practical platform for surface engineering, and will enable
reaching a substantial fraction of ∼1% solar flux reflection. The latter is
under development and will enable reaching > 1% reflection.

*Paper#05: Solid-particle stratospheric aerosol injection: a 2-D modelling
exploration of the design space*
https://stardustsrt.com/science/solid-particle-stratospheric-aerosol-injection
*Authors: *Yoav Lederer, Nahliel Wygoda, Dorri Halbertal and Brian E. J.
Rose
*Abstract*
Solid-particle alternatives to sulfate for stratospheric aerosol injection
(SAI) span a broad design space: particle composition and morphology,
sensitivities to agglomerate microphysics, and injection strategies in
latitude, altitude, and season. Spanning this space with three-dimensional
chemistry–climate models is practically prohibitive. To enable such sweeps,
we present a two-dimensional (2-D) zonal-mean modelling framework for SAI
with solid-particle materials. ERA5-constrained stratospheric transport is
coupled with explicit aerosol microphysics and a modified RRTMG radiative
transfer scheme, with each component extensively validated. Focusing on
silica and calcite, we use the framework to explore SAI performance across
two complementary axes: material properties together with monomer and
agglomerate microphysics, and injection strategies in space and time.
Tropical injection maximises radiative forcing efficacy but pays the
largest in-layer heating penalty. Coagulation in the tropical confinement
amplifies aggregate diameters and partially offsets the residence-time
advantage. A seasonal (alternating-summer-hemisphere) schedule delivers a
modest ∼ 10–30% mid-latitude cooling-efficacy gain over symmetric
injection, but at a comparable mid-latitude heating-cost penalty. For
IR-absorbing materials such as silica, symmetric mid-latitude injection
reduces stratospheric heating with limited loss of efficacy; calcite’s
negligible IR absorption keeps the heating penalty an order of magnitude
lower across all injection strategies considered.

*Paper#06: Uptake of stratospheric species on minerals proposed for
stratospheric aerosol injection*
https://stardustsrt.com/science/uptake-of-stratospheric-species
*Authors: *Anais Lostier, Yair Segev, Tzemah Kislev, Gal Schwartz Roitman,
Nadine Locoge, Manolis N. Romanias
*Abstract*
Solid mineral-based particles have been proposed as alternatives to
sulfates for climate intervention by stratospheric aerosol injection, as a
possible means for improving optical or chemical characteristics to thereby
minimize risks and uncertainties. However, the heterogeneous reactivity of
solid particles toward stratospheric trace gases, and possible implications
to the ozone layer, is currently not fully constrained, particularly at
stratospheric concentrations. Here we present a systematic comparative
study of the uptake of nitric acid (HNO3), hydrogen chloride (HCl), and
nitrogen dioxide (NO2) on four mineral surrogates, calcite, alumina,
crystalline silica (quartz), and amorphous silica, using complementary
Knudsen cell and flow-through reactor techniques. We find that NO2 uptake
is relatively weak on all surfaces, with estimated heterogeneous removal
timescales indicating negligible direct impact on stratospheric nitrogen
chemistry. Conversely, measuring HCl uptake over a concentration range
spanning five orders of magnitude, we find substantial uptake with a
pronounced concentration dependence consistent with surface site-limited
Langmuir adsorption. Extracting adsorption isotherms, we find that the
surface coverage of HCl at stratospheric concentrations differs by four
orders of magnitude between the surfaces, with calcite adsorbing the most
and amorphous silica the least, suggesting a dominant role of surface
acid-base character. Using HCl surface coverage as a proxy for the reactive
uptake coefficient of ClONO2, we estimate that amorphous silica could
produce substantially lower ozone depletion due to chlorine activation than
calcite or alumina under equivalent injection scenarios. We also find a
marked difference in uptake between the crystalline and amorphous forms of
silica, underscoring the sensitivity of heterogeneous chemistry to surface
microstructure and the importance of selecting particles with
low-reactivity surfaces, in addition to the consideration of bulk
characteristics. Our findings motivate the development of particles with
surfaces tailored for minimizing SAI risks and uncertainties, including
minimal reactivity with stratospheric gases and background sulfate aerosols.

*Paper#07: Feasibility Study for Industrial Scale Submicronic Engineered
Amorphous Silica Particle (SEASP) Manufacturing for Stratospheric Aerosol
Injection (SAI)*
https://stardustsrt.com/science/feasibility-study
*Authors: *Tamir Kuzurbardov, Avi Yaverboim, Tzemah Kislev, Eli Abramov
*Abstract*
A feasibility study is presented for scaling up manufacturing of
Submicronic Engineered Amorphous Silica Particles (SEASP) to industrial
throughput required for Stratospheric Aerosol Injection (SAI), with
properties meeting safety and functionality requirements [1,2].
Manufacturing is based on wet-precipitation chemistry via a TEOS-based
St¨ober sol-gel route. The goal of this study is to assess realistic
timescale and cost of manufacturing at relevant scales for SAI, analyze the
main risks and bottlenecks, and identify mitigation strategies for them.
Scale-up is assessed across the components necessary to establish
feasibility: process scalability, material availability, infrastructure,
operations, energy consumption, waste and by-products, timeline, and cost.

Based on relevant available data on SEASP manufacturing and
precipitated-silica scale-up benchmarks, it is assessed that scaling up
manufacturing from the current specialty chemical scale of 0.1 kt/yr to a
single module of 250 kt/yr is expected to be completed within approximately
five years. No fundamental technology or process show-stopper was
identified, provided that demand, logistics, financing, industrial
partnering, and regional manufacturing hubs are developed in parallel.

Plant replication of the 250 kt/yr module to regional hub manufacturing at
a climate-relevant scale of 1 Mt/yr, sufficient to offset a significant
fraction of decadal warming, is expected to be completed within two
additional years. An outlook is provided for further expansion toward
climate-scale 10 Mt/yr manufacturing capacity, required for approximately
1% solar-flux modification. This climate-scale capacity is expected to be
based on replicating the regional 1 Mt/yr hubs.

TEOS precursor availability is identified as the principal scale-up risk,
and an integrated TEOSSEASP manufacturing concept is presented to address
this risk. Unit economics of approximately USD 5/kg, dominated primarily by
raw-material costs, appear plausible, with further reductions possible
through process optimization, solvent recycling, continuous operation, and
precursor-route improvements.

*Source: Stardust*

-- 
You received this message because you are subscribed to the Google Groups 
"geoengineering" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To view this discussion visit 
https://groups.google.com/d/msgid/geoengineering/CAHJsh9-rNvdxgn7ROmcdgmLEZcJBASpQkttBPeP2Qjmn37x_YQ%40mail.gmail.com.

Reply via email to