----[Please read http://ercoupers.com/disclaimer.htm before following any advice in this forum.]----
Answers mixed in ---- [EMAIL PROTECTED] wrote: > > When Fred said the behavior of the plane was unacceptable, did > he mean that it would stall under full power > at 11 degrees up elevator at 1400 lb? Fred didn't describe the mis-behavior in detail. He just said that, under those conditions, the flying characteristics were not thought to be safe enough. With the 9 degrees of up travel, 1400 lb. gross weight and full power on my C-85, I get a pretty distinct break and then, with the yoke held full aft, I get a nearly level left turn that can't be overcome with aileron. With 11 degrees and the same conditions, I don't really want to go for the ride. > I just looked in Univair's catalogue & the split elevator > itself is listed at $1652 US (2623 can) & it looks > like that won't get me hinges or trim . I guess the next question is, > Just how much better is a coupe with > split elevator compared to one adjusted to 9 degrees? My guess is > that the climb rate will be pretty weak. Comparing the 9 degree up travel elevator versus the split elevator with 20 degrees of up travel, the only differences are: 1. Upon landing, with the split elevator, touch down is about 5-7 mph slower than with the 9 degree elevator. 2. You get not too much trim change when you go from idle to full power. This keeps you from that squirrely need to push on the yoke just after pushing full power on a go-around. This has no effect on climb, either max rate or max angle -- those are both done at higher airspeeds than the full up-elevator condition where the difference of the slip-stream over the elevator makes a difference. You can get your elevator rebuilt to have the split. Don't ask me how, I'm not a mechanic but competent mechanics told me it can be done. Get your paperwork approved before cutting metal. > > My reason for persuing this is that I am in the process of > buying a coupe in Canada (46 415c 85hp 1/2 fork 1260lb) > The owner is going right through it & he said he will get it changed > to a 1400 lb plane.The elevator is covered but > not painted yet. > I do want to use this coupe to land at the odd grass strip. Any more > thoughts or coments about this > are certainly welcome. > Darwin > I learned to fly my Coupe on an 1800' grass strip. I rarely took more than 1/2 the strip to break the ground. I was usually over 50' by the end of the runway but that's not quantified since we had no obstructions. Worse was a 2400' asphalt strip which took a lot more brakes to stop. Unless you have a very short strip or obstacles, I would say Coupes are as good a short-field plane as most. High-quality approach control IS necessary. If you want to do a lot of short-field stuff, get your prop pitched to a flat climb pitch. About three years after I bought my Coupe, my McCauley 1B90 prop was re-pitched to be 7146. It gives me pretty good climb for a 415-D and good take-off. The only time I COULDN'T get to 12,500' was on a hot afternoon in Nevada. I couldn't climb past 11,500' but then the density altitude was 14,500'. Some people say the 7146 pitch is not legal but the only specification I've found is the static rpm limit in the type certificate. With this pitch, my static rpm hits exactly on the upper limit. The downside is my 2400 rpm cruise speed is a proven 100 mph (give or take a few tenths). Ed Burkhead > [EMAIL PROTECTED] wrote: > >> I'm not sure where you're thinking of putting the vortex generators >> and for what purpose. >> >> The 9 degree up-travel limitation is because during flight testing at >> 1400 lb. gross weight at full up elevator and full power, the >> slip-stream pushed down on the elevator enough that the behavior of >> the plane was unacceptable. This was told to me directly by Coupe >> designer Fred Weick. >> >> The split elevator allows most of the slipstream to go through the >> split area so there's less down-push on the tail at full power and >> full up elevator. Thus the Coupe with a split elevator better >> approaches the ideal of a plane with similar behavior power on or >> power off (except of course for going up or down). >> >> I'd say the split elevator is the fix of choice. Be warned, some >> ^#$%%^ fool local FAA idiots may turn down your request to convert >> your elevator in spite of the fact that the split elevator was the >> FAA tested and approved factory solution to the 1400 lb. gross >> weight, full up elevator, full power problem. Get your paperwork >> signed off BEFORE doing work on the plane. >> >> Ed Burkhead >> N3802H, ERCO 415-D >> http://www.ercoupe.org >> >> Darwin Girdauckis <[EMAIL PROTECTED]> wrote: >> >> >----[Please read http://ercoupers.com/disclaimer.htm before >> following any advice in this forum.]---- >> > >> >Just posting to say hi & ask a couple of questions. >> >Has anyone ever put vortex generators on a coupe? >> >I understand that to bring a 415c up to 1400 lb gross >> >you have to reduce the elevator up deflection to 9 degrees. >> >in order to retain stall prevention. If vortex generators were >> >used, couldn't they do the job allowing you to keep it at >> >11 degrees? If this has been talked to death already please >> >forgive me as I'm new to this group. >> > >> >funflyer >> > >> > >> > >> >> __________________________________________________________________ >> Your favorite stores, helpful shopping tools and great gift ideas. >> Experience the convenience of buying online with [EMAIL PROTECTED] >> http://shopnow.netscape.com/ >> >> Get your own FREE, personal Netscape Mail account today at >> http://webmail.netscape.com/ >> ==^================================================================ This email was sent to: [EMAIL PROTECTED] EASY UNSUBSCRIBE click here: http://topica.com/u/?aVxiLm.aVzvvT Or send an email to: [EMAIL PROTECTED] T O P I C A -- Register now to manage your mail! http://www.topica.com/partner/tag02/register ==^================================================================
<<attachment: winmail.dat>>
