Michael, For your situation, you would want to use something like gluster volume create <volume name> replica 2 node1:/export/bricks/a node2:/export/bricks/a node1:/export/bricks/b node2:/export/bricks/b etc...
You are correct that the order in which you specify the volume is how the pairing will occur. Specifying replica 2 means there will always be at least two copies of the data, and if one of the nodes goes down, the other will pick up automatically. Thanks, Eco ----- Original Message ----- From: "Michael Peek" <p...@nimbios.org> To: Gluster-users@gluster.org Sent: Monday, July 8, 2013 8:46:47 AM Subject: [Gluster-users] Is it possible to manually specify brick replication location? Hi Gluster gurus, I'm new to Gluster, so if there is a solution already talked about somewhere then gladly point me to it and I'll get out of the way. That said, here's my problem: I have four machines. Each machine is running Ubuntu 12.04 with Gluster 3.2.5. Each machine has two drives: node1:/export/bricks/a node1:/export/bricks/b node2:/export/bricks/a node2:/export/bricks/b node3:/export/bricks/a node3:/export/bricks/b node4:/export/bricks/a node4:/export/bricks/b I created a volume with a single replication, added the bricks, mounted it to /mnt, and then created a file with "touch /mnt/this". The file "this" appeared on the two bricks located on node1: node1:/export/bricks/a/this and node1:/export/bricks/b/this So if node1 goes down, all access to the file "this" is lost. It seemed to me that the order in which bricks were added dictated the replication location -- i.e. the second brick added is used as the replication destination for the first brick, and so on with the 3rd and 4th pair of bricks, 5th and 6th, etc. I've searched the archives, and this seems to be confirmed in a past post located here: http://supercolony.gluster.org/pipermail/gluster-users/2013-June/036272.html Replica sets are done in order that the bricks are added to the volume. ... So, you have an issue here, that both bricks of a replica set are on the same host. Unfortunately, this was the end of the thread and no more information was forthcoming. Now, I'm just starting out, and my volume is not yet used in production, so I have the luxury of removing all the bricks and then adding them back in an order that allows for replication to be done across nodes the way that I want. But I see this as a serious problem. What happens down the road when I need to expand? How would I add another machine as a node, and then add it's bricks, and still have replication done outside of that one machine? Is there a way to manually specify master/replication location? Is there a way to reshuffle replicant brick on a running system? A couple of solutions have presented themselves to me: 1) Only add new nodes in pairs, and make sure to add bricks in the correct order. 2) Only add new nodes in pairs, but setup two Gluster volumes and use geo-replication (even though the geographical distance between the two clusters may be as little as only 1 inch). 3) Only add new nodes in pairs, and use RAID or LVM to glue the drives together, so that as far as Gluster is concerned, each node only has one brick. But each of these solutions involves adding new nodes in pairs, which increases the incremental cost of expansion more than it feels like it should. It just seems to me that there should be a smarter way to handle things than what I'm seeing before me, so I'm hoping that I've just missed something obvious. So what is the common wisdom among seasoned Gluster admins? Thanks for your help, Michael _______________________________________________ Gluster-users mailing list Gluster-users@gluster.org http://supercolony.gluster.org/mailman/listinfo/gluster-users _______________________________________________ Gluster-users mailing list Gluster-users@gluster.org http://supercolony.gluster.org/mailman/listinfo/gluster-users
