Hi,
This patch implements grub-install on coreboot. Since there's no pre-defined
boot protocol on this platform, we simply generate a usable Multiboot image
and dump it to /boot. User can afterwards load it to flash to make the board
boot using this disk, or load it from elsewhere (even from a BIOS rescue disk).
I hope it's not too intrusive to reuse i386-pc's grub-install; I think it's
much better than duplicating the whole script.
Note: indentation changes intentionally ommitted to improve readability.
--
Robert Millan
The DRM opt-in fallacy: "Your data belongs to us. We will decide when (and
how) you may access your data; but nobody's threatening your freedom: we
still allow you to remove your data and not access it at all."
2008-11-22 Robert Millan <[EMAIL PROTECTED]>
* conf/i386-coreboot.rmk (sbin_SCRIPTS): Add `grub-install'.
(grub_install_SOURCES): New variable.
* util/i386/pc/grub-install.in: Add a few condition checks to make it
usable on coreboot.
Index: conf/i386-coreboot.rmk
===================================================================
--- conf/i386-coreboot.rmk (revision 1926)
+++ conf/i386-coreboot.rmk (working copy)
@@ -90,6 +90,9 @@ grub_emu_SOURCES = commands/boot.c comma
grub_emu_LDFLAGS = $(LIBCURSES)
+sbin_SCRIPTS += grub-install
+grub_install_SOURCES = util/i386/pc/grub-install.in
+
# Modules.
pkglib_MODULES = _linux.mod linux.mod normal.mod \
_multiboot.mod multiboot.mod aout.mod \
Index: util/i386/pc/grub-install.in
===================================================================
--- util/i386/pc/grub-install.in (revision 1926)
+++ util/i386/pc/grub-install.in (working copy)
@@ -32,7 +32,11 @@ [EMAIL PROTECTED]@
pkglibdir=${libdir}/`echo ${PACKAGE_TARNAME}/${target_cpu}-${platform} | sed ${transform}`
grub_setup=${sbindir}/`echo grub-setup | sed ${transform}`
+if [ "${target_cpu}-${platform}" = "i386-pc" ] ; then
grub_mkimage=${bindir}/`echo grub-mkimage | sed ${transform}`
+else
+grub_mkimage=${bindir}/`echo grub-mkelfimage | sed ${transform}`
+fi
grub_mkdevicemap=${sbindir}/`echo grub-mkdevicemap | sed ${transform}`
grub_probe=${sbindir}/`echo grub-probe | sed ${transform}`
rootdir=
@@ -152,6 +156,7 @@ device_map=${grubdir}/device.map
grub_probe="${grub_probe} --device-map=${device_map}"
+if [ "${target_cpu}-${platform}" = "i386-pc" ] ; then
# Check if GRUB is installed.
set $grub_setup dummy
if test -f "$1"; then
@@ -160,6 +165,7 @@ else
echo "$1: Not found." 1>&2
exit 1
fi
+fi
set $grub_mkimage dummy
if test -f "$1"; then
@@ -210,9 +216,14 @@ for file in ${grubdir}/*.mod ${grubdir}/
rm -f $file || exit 1
fi
done
-for file in ${pkglibdir}/*.mod ${pkglibdir}/*.lst ${pkglibdir}/*.img; do
+for file in ${pkglibdir}/*.mod ${pkglibdir}/*.lst; do
+ cp -f $file ${grubdir} || exit 1
+done
+if [ "${target_cpu}-${platform}" = "i386-pc" ] ; then
+for file in ${pkglibdir}/*.img; do
cp -f $file ${grubdir} || exit 1
done
+fi
# Write device to a variable so we don't have to traverse /dev every time.
grub_device=`$grub_probe --target=device ${grubdir}`
@@ -234,7 +245,12 @@ partmap_module=`$grub_probe --target=par
devabstraction_module=`$grub_probe --target=abstraction --device ${grub_device}`
# The order in this list is critical. Be careful when modifying it.
-modules="$modules $fs_module $partmap_module biosdisk $devabstraction_module"
+if [ "${target_cpu}-${platform}" = "i386-pc" ] ; then
+ modules="$modules biosdisk"
+else
+ modules="$modules ata"
+fi
+modules="$modules $fs_module $partmap_module $devabstraction_module"
prefix_drive=
if [ "x${devabstraction_module}" = "x" ] ; then
@@ -248,7 +264,16 @@ if [ "x${devabstraction_module}" = "x" ]
# Strip partition number
install_drive="`echo ${install_drive} | sed -e s/,[0-9]*//g`"
grub_drive="`echo ${grub_drive} | sed -e s/,[0-9]*//g`"
- if [ "x${grub_drive}" != "x${install_drive}" ] ; then
+ if [ "${target_cpu}-${platform}" != "i386-pc" ] ; then
+ # generic method (used on coreboot)
+ uuid="`$grub_probe --target=fs_uuid --device ${grub_device}`"
+ if [ "x${uuid}" = "x" ] ; then
+ echo "UUID needed on this platform, but the filesystem containing ${grubdir} does not support UUIDs." 1>&2
+ exit 1
+ fi
+ prefix_drive="(UUID=${uuid})"
+ modules="$modules fs_uuid"
+ elif [ "x${grub_drive}" != "x${install_drive}" ] ; then
uuid="`$grub_probe --target=fs_uuid --device ${grub_device}`"
if [ "x${uuid}" = "x" ] ; then
echo "You attempted a cross-disk install, but the filesystem containing ${grubdir} does not support UUIDs." 1>&2
@@ -266,12 +291,20 @@ if [ "x${relative_grubdir}" = "x" ] ; th
relative_grubdir=/
fi
+if [ "${target_cpu}-${platform}" = "i386-pc" ] ; then
+
$grub_mkimage --output=${grubdir}/core.img --prefix=${prefix_drive}${relative_grubdir} $modules || exit 1
# Now perform the installation.
$grub_setup ${setup_verbose} --directory=${grubdir} --device-map=${device_map} \
${install_device} || exit 1
+else
+
+$grub_mkimage -d ${pkglibdir} --output=/boot/multiboot.img --prefix=${prefix_drive}${relative_grubdir} $modules || exit 1
+
+fi
+
# Prompt the user to check if the device map is correct.
echo "Installation finished. No error reported."
echo "This is the contents of the device map $device_map."
_______________________________________________
Grub-devel mailing list
[email protected]
http://lists.gnu.org/mailman/listinfo/grub-devel