Joe, you make some excellent points here regarding variations in chips
and other parts.
One additional comment is that the percentage level for the battery is
not always accurate. This is a problem not only with the sense
notetakers, but with those of other manufacturers as well.
A warning message at, say, 5 percent would really be nice, but because
these battery level indicators can vary so widely depending on
components, usage, temperature, and many other factors, the madevelopers
have to factor in a margin of error so you won't suddenly have a
battery go flat with no warning at all.
I get tired of the repeated battery low messages as well, but I'd like
it even less if my battery went flat with no warning.
As for the sense not continuing to read following a low battery message,
I think I have heard of this on one or maybe two other occasions, but my
wife and I each have a bsp and neither of our units have ever exhibited
the stopping of reading.
Maybe Raul can comment further on this whole subject.
Don
----- Original Message -----
From: "Joe Giovanelli" <[email protected]>
To: <[email protected]>
Sent: Sunday, September 06, 2009 12:46 PM
Subject: Re: [GWN] A definite annoyance
Hello, Tessa and Others,
Even though Braille Sense 32's are all made using the same parts,
there are tiny variations between any group of the same components.
Let's take an audio chip. This chip will pass inspection and will
right properly, but there will be a difference from that chip to the
next, and both will still operate properly. If we add up all the
slight variations among components, we will still have a good, working
Braille Sense, but it is very likely that one unit may fail to work
when the battery has only 10 per cent of full capacity, but another
one will continue to work properly at a battery capacity of only 5 per
cent.
To compensate for this, HIMS wisely warns of a possible drop out well
before such a drop out will happen. We know that no unit will fail
when its battery is at the 15 per cent level, but we don't know how
much lower the battery voltage will have to be before a complete shut
down will occccur.
Let's be glad that we are warned soon enough so we can take action by
saving our work while there's time.
Yes, it's annoying to be reminded about this every minute, but it's
better than having a failure because you continued working for too
long after that 15 per cent is reached. I definitely would not
recommend dropping these reminders. I don't ever get down to 15 per
cent. I don't want to be reminded of low battery power.
Forget about 15 per cent. Charge the unit when it's convenient. As I
write this, I show 73 per cent charged. I won't charge it now, but
when I do, it will be at a time when I won't be using the unit and
before the charge falls below 20 per cent. I seldom even get that
low.
If you operate your unit this way, nothing will annoy you about a need
to charge the battery.
Joe G.
----- Original Message -----
From: "Tessa" <[email protected]>
To: <[email protected]>
Date: Sunday, Sep 6, 2009 12:08:13
Subject: Re: [GWN] A definite annoyance
I don't mind the fact that the bs alerts me to the 15% charge, what I
do
mind is that my machine stops reading every time it gives me the
warning
message, so if it goes off every minute then every minute I have to
tell it
to continue reading until I get too frustrated and plug it in. Sure,
tell me
when I'm at 15% and 14% and 13% but don't remind me of the fact every
minute
and don't quit reading.
But from the sounds of it only some and not all bsp's stop reading
which I
find a touch odd, perhaps Rawl could address this?
Tessa
----- Original Message -----
From: "Terri Pannett" <[email protected]>
To: <[email protected]>
Sent: Sunday, September 06, 2009 11:30 AM
Subject: Re: [GWN] A definite annoyance
I think HIMS purposely set the VS and BSP to remind us when the
battery
reaches 15%.
I don't like seeing extraneous dots, either, but I have been
experimenting
and I believe another reason for extraneous dots is so the speech
will say
the text correctly. HIMS must be implementing the Duxbury translator
differently from HumanWare. They haven't been around as long, so
they still
have much to learn.
As for BANA rules, all versions of Duxbury follow them as closely as
possible. Remember that originally braille translation software was
designed to translate text from print to braille so blind people
could
receive braille material faster. Because many blind people prefer
writing
in braille but they have the need to translate the braille into print
for
sighted people to read, the software can translate braille to print,
but it
has some hurdles to overcome.
The Sense notetakers don't support UEB, thank heavens! I hope the
code will
never be adopted here in the U.S. for reasons I have stated on
another list.
Terri Amateur Radio call sign KF6CA.
----- Original Message -----
From: "Olusegun -- Victory Associates LTD, Inc."
<[email protected]>
To: <[email protected]>
Sent: Friday, September 04, 2009 7:08 PM
Subject: Re: [GWN] A definite annoyance
> Hello Tessa:
>
> The BSP does the same thing: Gets down to 15% and issues a warning
> every
> minute thereafter. I suppose it assumes I am COMPLETELY BRAIN DEAD
> and
> need the frequent reminder. I detest it too and wish the bug will
> be
> fixed with the next upgrade.
>
> I also detest the fact that I CANNOT DECIDE whether or not I want
> extraneous dots here and there on the display: Example: Inserting
> a dot
> 4 before the SLASH sign. I DO NOT wish to be bothered by BANA
> rules as I
> practically EMPLOY BRAILLE FOR MY OWN USES ONLY. Those extraneous
> dots
> WASTE SPACE and slows down my reading too much.
>
> Sincerely,
> Olusegun
> Denver, Colorado
>
> __________ Information from ESET NOD32 Antivirus, version of virus
> signature database 4399 (20090905) __________
>
> The message was checked by ESET NOD32 Antivirus.
>
> http://www.eset.com
>
>
>
__________ NOD32 4401 (20090906) Information __________
This message was checked by NOD32 antivirus system.
http://www.eset.com