Applied both Goo Gone and pure d-limonene liberally to an edge of a polyiso board. Let it soak in. Waited about five minutes. Rubbed the spots vigorously with a piece of paper towel. See no sign of deleterious effect. Have used it on Mylar in the past with no negative consequences, either. Think it might help you. Might need more than I said earlier. Probably be worth it to buy the 16 oz. size.
On Sep 17, 2017 3:54 PM, "ken winston caine" <ken.winston.ca...@gmail.com> wrote: Haven't tested this with hexayurt bifilament tape. However, d-limonene tends to be an excellent natural solvent for most gums and tape adhesives. It's found in commercial products like Citri-Solv and Goo Gone, both readily available in small, inexpensive containers. (As well as in industrial-size gallon jugs for use as a drain cleaner and degreaser. And in food-grade gallons as a natural citrus flavoring.) A 6 or 8 oz. bottle is all you'd need. I will rub some on polyiso this afternoon to make sure it doesn't dissolve it, and report back. On Sep 17, 2017 9:11 AM, <hexayurt@googlegroups.com> wrote: hexayurt@googlegroups.com <https://groups.google.com/forum/?utm_source=digest&utm_medium=email#!forum/hexayurt/topics> Google Groups <https://groups.google.com/forum/?utm_source=digest&utm_medium=email/#!overview> <https://groups.google.com/forum/?utm_source=digest&utm_medium=email/#!overview> Topic digest View all topics <https://groups.google.com/forum/?utm_source=digest&utm_medium=email#!forum/hexayurt/topics> - Removing tape <#m_6232495786046258893_m_-2119355705466232307_m_353747427191902757_group_thread_0> - 1 Update Removing tape <http://groups.google.com/group/hexayurt/t/a7eb9988e4ac54b9?utm_source=digest&utm_medium=email> Bob Hearn <bob.he...@gmail.com>: Sep 16 11:26AM -0700 I'm rebuilding my H12 into a 5 1/2-yurt. The leftover tape is a pain for beveling (panels were unbeveled), but more importantly, when I apply the new hinging I don't think I want to do it over old tape, even if was protected with aluminum. But trying to remove it just messes up the panel. Yes, I know panels are cheap, but I can't quite make myself just throw away a perfectly good yurt when it can supply all the materials for the new one. Does anyone have a better idea than just leaving them out in the sun for a few weeks (after removing the aluminum tape)? Maybe some kind of UV lamp, or solvent, to accelerate the process? My wife is not too thrilled with them sitting on the deck, so I'm laying them out on the (flat) roof, but at this point, the effort definitely does not seem worth the $20 / panel to replace them with new. Back to top <#m_6232495786046258893_m_-2119355705466232307_m_353747427191902757_digest_top> You received this digest because you're subscribed to updates for this group. You can change your settings on the group membership page <https://groups.google.com/forum/?utm_source=digest&utm_medium=email#!forum/hexayurt/join> . To unsubscribe from this group and stop receiving emails from it send an email to hexayurt+unsubscr...@googlegroups.com. -- You received this message because you are subscribed to the Google Groups "hexayurt" group. To unsubscribe from this group and stop receiving emails from it, send an email to hexayurt+unsubscr...@googlegroups.com. To post to this group, send email to hexayurt@googlegroups.com. Visit this group at https://groups.google.com/group/hexayurt. For more options, visit https://groups.google.com/d/optout.