Do you have to tell PSF what port to use? I have PORTNO=5001 set up to print to my XEROX printer in my PSF proc segment.
-----Original Message----- From: IBM Mainframe Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Matt Dazzo Sent: Wednesday, April 02, 2008 2:25 PM To: IBM-MAIN@BAMA.UA.EDU Subject: TCPIP IPDS Printer Setting up an IBM 6500 as a JES2 PSF printer. I am unable to get it to print through jes but did get to print using Macro4's vtamprint product over tcpip. So the network and TCPIP appear to be ok. I included pieces of my jes2 config and psf proc, also the psf listing. Any ideas what might be holding things up? If this is the incorrect forum for this question please direct, thanks. PSF proc segment. //PRT6 CNTL //PRT6 PRINTDEV FONTDD=*.FONT01, /* FONT LIBRARY DD */ // OVLYDD=*.OLAY01, /* OVERLAY LIBRARY DD */ // PSEGDD=*.PSEG01, /* SEGMENT LIBRARY DD */ // PDEFDD=*.PDEF01, /* PAGEDEF LIBRARY DD */ // FDEFDD=*.FDEF01, /* FORMDEF LIBRARY DD */ // JOBHDR=*.JOBHDR, /* JOB HEADER SEPARATOR */ // JOBTRLR=*.JOBTLR, /* JOB TRAILER SEPARATOR */ // DSHDR=*.DSHDR, /* DATA SET HEADER SEPARATOR */ // MESSAGE=*.MSGDS, /* MESSAGE DATA SET OUTPUT */ // BUFNO=15, /* NUMBER OF WRITE DATA BUFFERS*/ // PAGEDEF=L06464, /* DEVICE PAGEDEF DEFAULT */ // FORMDEF=Q50010, /* DEVICE FORMDEF DEFAULT */ // CHARS=GT10, /* DEVICE DEFAULT FONT */ // PIMSG=YES, /* YES PRINT ALL PSF MESSAGES */ // DATACK=BLOCK, /* NO REPORT DATA-CHECK ERRORS*/ // TRACE=NO, /* NO INTERNAL TRACEING */ // SETUP=FORMS, /* ISSUE SETUP MSG */ // FAILURE=WCONNECT, /* WAIT FOR CONNECT */ // CONNINTV=600, /* ATTEMPT CONN FOR 10 MIN */ // DISCINTV=15, /* STAY CONN W/PRINTER WHEN IDLE */ // MGMTMODE=IMMED, /* START COMM W/PRINTER */ // IPADDR='27.1.39.76' /* TCPIP ADDR */ //PRT6 ENDCNTL JES2 Parms /*-------- FUNCTIONAL SUBSYSTEM DEFINITION PARAMETERS ------------*/ FSSDEF(FSS1) PROC=FSS1001, /* SYS4.PROCLIB MEMBER TO START ASI. */ AUTOSTOP=NO, /* DO NOT STOP ASI WHEN ALL PRT DRAIN */ HASPFSSM=HASPFSSM /* LOAD MODULE NAME. */ /* */ /*---------------- LOCAL PRINTER PARAMETERS ----------------------*/ /*------------------------------------------------------------------*/ PRT(6) BURST=NO, /* NO BURST FEATURE ON THIS UNIT */ CLASS=A, /* INITIAL OUTPUT QUEUE TO PROCESS */ CKPTMODE=PAGE, /* CHECK POINTS COUNTS ARE PAGES */ CKPTPAGE=100, /* 100 PAGES BETWEEN CHECK POINTS */ COPYMARK=DATASET, /* COPYMARK TO CHANGE EVER DATA SET */ FCB=8, /* FORMS CONTROL BUFFER NAME = P18 */ FSS=FSS1, /* FUNCTIONAL SUBSYSTEM NAME */ MARK=YES, /* YES 3800 EDGE MARKS USED */ MODE=FSS, /* INITIALLY STARTED IN FSS MODE */ PRESELCT=NO, /* SELECT TWO REPORTS AT A TIME */ PRMODE=(LINE,PAGE), /* TYPE OUTPUT TO BE DIRECTED */ SEP=YES, /* YES SEPARATOR PAGES */ SEPCHARS=DEFAULT, /* DEFAULT FONT FOR SEPARATOR PAGES */ SEPDS=NO, /* NO HEADER SEPARATOR PAGES WANTED */ START=NO, /* AUTO-START PRINTER? NO */ TRKCELL=NO, /* YES DESPOOL THE COMPLETE TRACK */ UCS=GT12, /* X0GT12 CHARATER SET NAME TO LOAD */ WS=(W,R,Q,PMD,LIM,F/C,P) /* WORK SELECTION CRITERIA */ FSS1 Messages STC04403 $HASP373 FSS1001 STARTED STC04403 IEF403I FSS1001 - STARTED - TIME=15.01.02 STC04403 APS621I FSS1001 FSS1 *** OPERATOR INTERFACE INITIALIZED FOR 400 (CONT.) PSF 3.4.0 FOR z/OS. STC04403 APS933I FSS1001 FSS1 *** PRT6 (TCPIP) PRINTER INFORMATION, 401 (CONT.) DEV=6500, IBM INFOPRINT 6500, ECLEVEL=000000000, (CONT.) ADDR=27.1.39.76, SYSNAME=SYS1, CPUID=00024E7E2086, ATTACH=PSF. STC04403 APS929I FSS1001 FSS1 *** PRT6 (TCPIP) COMMUNICATION WITH 404 (CONT.) TCP/IP-ATTACHED PRINTER (PRT6) IPADDR (27.1.39.76) WAS (CONT.) TERMINATED DUE TO A DISCONNECT INTERVAL TIMEOUT. STC04403 APS933I FSS1001 FSS1 *** PRT6 (TCPIP) PRINTER INFORMATION, 405 (CONT.) DEV=6500, IBM INFOPRINT 6500, ECLEVEL=000000000, (CONT.) ADDR=27.1.39.76, SYSNAME=SYS1, CPUID=00024E7E2086, ATTACH=PSF. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
