Well Dana wins the prize - this was something I definitely did not know, but once I remove the criteria the offloads both started.
This is why I love this forum! Thanks for the help. -----Original Message----- From: IBM Mainframe Discussion List [mailto:IBM-MAIN@LISTSERV.UA.EDU] On Behalf Of Dana Mitchell Sent: Thursday, September 13, 2018 10:28 AM To: IBM-MAIN@LISTSERV.UA.EDU Subject: Re: Strange JES2 SPOOL Offload issue Specifying a minus sign (-) before a criterion causes that criterion to be removed from the list. $TOFF1.ST,WS=(/) $HASP886 OFF1.ST 969 $HASP886 OFF1.ST STATUS=STARTABLE,CREATOR=,DISP=DELETE, $HASP886 OUTDISP=(WRITE,KEEP),HOLD=,JOBNAME=,NOTIFY=NO, $HASP886 RANGE=(J1,999999),ROUTECDE=(),START=YES, $HASP886 VOLUME=(,,,),WS=(Q,OUTD/),BURST=,FCB=,FLASH=, $HASP886 FORMS=(,,,,,,,),LIMIT=(0,*),PLIM=(0,*), $HASP886 PRMODE=(),QUEUE=,UCS=,WRITER= $TOFF1.ST,WS=(-Q/) $HASP886 OFF1.ST 971 $HASP886 OFF1.ST STATUS=STARTABLE,CREATOR=,DISP=DELETE, $HASP886 OUTDISP=(WRITE,KEEP),HOLD=,JOBNAME=,NOTIFY=NO, $HASP886 RANGE=(J1,999999),ROUTECDE=(),START=YES, $HASP886 VOLUME=(,,,),WS=(OUTD/),BURST=,FCB=,FLASH=, $HASP886 FORMS=(,,,,,,,),LIMIT=(0,*),PLIM=(0,*), $HASP886 PRMODE=(),QUEUE=,UCS=,WRITER= $TOFF1.ST,WS=(-OUTD) $HASP886 OFF1.ST 973 $HASP886 OFF1.ST STATUS=STARTABLE,CREATOR=,DISP=DELETE, $HASP886 OUTDISP=(WRITE,KEEP),HOLD=,JOBNAME=,NOTIFY=NO, $HASP886 RANGE=(J1,999999),ROUTECDE=(),START=YES, $HASP886 VOLUME=(,,,),WS=(/),BURST=,FCB=,FLASH=,FORMS=(, $HASP886 ,,,,,,),LIMIT=(0,*),PLIM=(0,*),PRMODE=(), $HASP886 QUEUE=,UCS=,WRITER= HTH Dana On Thu, 13 Sep 2018 09:05:40 -0500, Todd Burrell <todd_burr...@csx.com> wrote: >I'm playing around with JES2 SPOOL OFFLOAD on our test system and I want to be >able to try and offload everything from the spool to test out timing. I have >changed both of my transmitters to have DISP=KEEP to make the offload >no-destructive. > >However, once I start the offload it does not select anything, and when I try >and do $TOFF2.ST,WS=(/), JES2 just ignores this and keeps the same selection >criteria I had before I did the command? I have everything else pretty much >blanked out for selection criteria, but for some reason JES2 ignores my $TOFF >command to change the WS settings? > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN This email transmission and any accompanying attachments may contain CSX privileged and confidential information intended only for the use of the intended addressee. Any dissemination, distribution, copying or action taken in reliance on the contents of this email by anyone other than the intended recipient is strictly prohibited. If you have received this email in error please immediately delete it and notify sender at the above CSX email address. Sender and CSX accept no liability for any damage caused directly or indirectly by receipt of this email. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN