Hi Joseph, Currently, vendors have chosen some undisclosed big numbers for the reassembly buffer on the tunnel interface Or no buffer at all for tunnels that do not support reassembly. That does not create any additional restriction for MTU. Nobody did believe (IPv4 or IPv6 – does not matter) that buffer requirements for end nodes are applicable for transit nodes. Your liberty to apply the requirements and terminology of one to the other is not a good idea. draft-ietf-intarea-tunnels propose to decrease reassembly buffer to “typical host EMTU_R (1500B) minus tunnel outer headers overhead” that would cause additional fragmentation.
As the compromise: Could you change the default for “draft-ietf-intarea-tunnels Tunnel MTU” (reassembly buffer) to 9k? (to reflect reality) I would still be not happy in the mail to any alias about calling parameters of transit node buffer by the terminology of end node buffer. But if you would not create additional fragmentation – I would not have any complains in my draft in regards to draft-ietf-intarea-tunnels. It could be the resolution. Well, probably it is not a good compromise, because you have the logic through all your document. 9k (reality) would protrude out of your logic. The logic itself is good. It is broken because the most basic assumption is wrong (before you did apply any logic). The Data Plane on transit nodes should not behave as the Control Plane on transit nodes or Transport Layer on end nodes! It was the wrong assumption initially. Buffers should be different. Names should be different. Unification here is not possible. It would be rejected by vendors anyway because reassembly is expensive, the one who would increase it – would get a competitive disadvantage. It is easy to translate additional reassembly to $$ losses. Eduard From: Joseph Touch [mailto:[email protected]] Sent: Tuesday, March 23, 2021 10:44 PM To: Vasilenko Eduard <[email protected]> Cc: [email protected]; int-area <[email protected]> Subject: Re: Proxy function for PTB messages on the tunnel end On Mar 23, 2021, at 12:10 PM, Vasilenko Eduard <[email protected]<mailto:[email protected]>> wrote: Hi Joseph, I am not much interested to discuss IPv4 now. (despite that 2 MTUs for one interface is absent there too) Let’s look at your reference to RFC 8200. Section 4.5: unlike IPv4, fragmentation in IPv6 is performed only by source nodes, not by routers along a packet's delivery path It means that all these discussions about fragmentation and reassembly are not related to transit nodes. It is for the “source and destination nodes”. Agreed. The better terminology is “transit node”, “destination node” – like it is in RFC 8200, not “host” or “router”. Please see section 2 of RFC8200 (color added by me): 2<https://tools.ietf.org/html/rfc8200#section-2>. Terminology node a device that implements IPv6. router a node that forwards IPv6 packets not explicitly addressed to itself. (See Note below.) host any node that is not a router. (See Note below.) The term “transit node” does no appear in RFC8200. The terms “source node” and “destination node” are used in RFC8200 but not defined in Sec 2. They are clearly hosts that originate IPv6 packets and hosts that consume IPv6 packets, respectively. In an IPv6 tunnel, the tunnel ingress emits new packets with IP headers it adds using its IP address. That makes it a source node. Same for how the egress consumes those packets. From the perspective of the tunnel path, the ingress and egress are hosts and intermediate hop relays are routers. From the perspective of the overall path, the tunnel is a link, either host/host, host/router, router/host, or router/router. A tunnel is not itself a router, however. You see – nobody is asking vendors to be compliant with any reassembly buffers in transit. Because it was assumed that would be not reassembly at transit. Reassembly happens at tunnel egresses whether you want it to or not. Hence, vendors had the freedom to choose a much bigger number than 1500 when reassembly did happen in reality (despite IPv6 architecture decisions). 1500 is the IPv5 minimum EMTU_R; vendors can always implement larger reassembly when they choose to. Please, show any evidence (or just claim if you could not disclose) that any vendor has 1500B (or less) for reassembly in the data plane (on transit node). Here’s how to do it: - set interfaces to use 1280B packets - setup an IPv6 tunnel - send a 1280B packet through that tunnel If you don’t implement reassembly, it won’t work. But it does. Everywhere. I neither know nor care. That’s a compliance issue, not a standards issue. It is not a compliance issue, because there is no regulation/standard to comply with. Vendors had the freedom and solved the problem easily. RFC8200 is the standard. Tunnel ingresses and egresses create and consume packets, so they act as hosts. I don’t care if they’re implemented on routers; routers implement lots of things as hosts (see e.g., RFC4201, Sec 3.1: ...A compliant host implementation MUST support (a) and (c) and a compliant security gateway must support all three of these forms of connectivity, since under certain circumstances a security gateway acts as a host This is described in detail in: RFC1858 RFC4459 RFC4944 RFC6946 RFC6980 RFC7588 RFC8021 RFC8900 I did not ask for a general discussion. Of course, fragmentation is a big topic with many publications. You asked for *specific examples* of what vendors do. Those RFCs provide them. I did ask for any evidence that there is 2 MTU per 1 virtual interface and fragmentation problem as the result of this (when packet would come in between of these MTUs). I don’t see why you’re stuck on this issue. Because you are trying to introduce additional fragmentation to the area where it was absent before. The root cause is the introduction of the second MTU per interface (that is in the reality the buffer size). I have not introduced anything; I am describing an existing requirement of any device that consumes IP packets (i.e., acts as an IP destination). When it does so, it is a host. Tunnel egresses do that. 2 MTUs for one interface is the innovation. It does not exist in any standard or any real implementation. It is invented only in draft-ietf-intarea-tunnels. It is not just new names and new classification. It new things that does not exist in the real world. Harmful, because of additional fragmentation introduced.. Draft-tunnels has been discussed and reviewed by int-area for over a decade. Nobody else has agreed with your assertions. Joe
_______________________________________________ Int-area mailing list [email protected] https://www.ietf.org/mailman/listinfo/int-area
