Only two things needed adjustment:
- pipe select for PCH_CPT
- There's no dithering bit on ilk+ in the lvds ctl reg
Signed-off-by: Daniel Vetter <daniel.vet...@ffwll.ch>
---
drivers/gpu/drm/i915/intel_display.c | 40 ------------------------------------
drivers/gpu/drm/i915/intel_lvds.c | 24 ++++++++++++++--------
2 files changed, 15 insertions(+), 49 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_display.c
b/drivers/gpu/drm/i915/intel_display.c
index bd3fa2b..68c0524 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -5324,7 +5324,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
bool ok, has_reduced_clock = false;
bool is_lvds = false, is_dp = false, is_cpu_edp = false;
struct intel_encoder *encoder;
- u32 temp;
int ret;
bool dither, fdi_config_ok;
@@ -5387,45 +5386,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
} else
intel_put_pch_pll(intel_crtc);
- /* The LVDS pin pair needs to be on before the DPLLs are enabled.
- * This is an exception to the general rule that mode_set doesn't turn
- * things on.
- */
- if (is_lvds) {
- temp = I915_READ(PCH_LVDS);
- temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
- if (HAS_PCH_CPT(dev)) {
- temp &= ~PORT_TRANS_SEL_MASK;
- temp |= PORT_TRANS_SEL_CPT(pipe);
- } else {
- if (pipe == 1)
- temp |= LVDS_PIPEB_SELECT;
- else
- temp &= ~LVDS_PIPEB_SELECT;
- }
-
- /* set the corresponsding LVDS_BORDER bit */
- temp |= dev_priv->lvds_border_bits;
- /* Set the B0-B3 data pairs corresponding to whether we're
going to
- * set the DPLLs for dual-channel mode or not.
- */
- if (clock.p2 == 7)
- temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
- else
- temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
- /* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
- * appropriately here, but we need to look more thoroughly into
how
- * panels behave in the two modes.
- */
- temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
- if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
- temp |= LVDS_HSYNC_POLARITY;
- if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
- temp |= LVDS_VSYNC_POLARITY;
- I915_WRITE(PCH_LVDS, temp);
- }
-
if (is_dp && !is_cpu_edp) {
intel_dp_set_m_n(crtc, mode, adjusted_mode);
} else {
diff --git a/drivers/gpu/drm/i915/intel_lvds.c
b/drivers/gpu/drm/i915/intel_lvds.c
index 057e29a..b4025c1 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -104,17 +104,20 @@ static void intel_pre_pll_enable_lvds(struct
intel_encoder *encoder)
int pipe = intel_crtc->pipe;
u32 temp;
- /* pch split platforms are not yet converted. */
- if (HAS_PCH_SPLIT(dev))
- return;
-
temp = I915_READ(lvds_encoder->reg);
temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
- if (pipe == 1) {
- temp |= LVDS_PIPEB_SELECT;
+
+ if (HAS_PCH_CPT(dev)) {
+ temp &= ~PORT_TRANS_SEL_MASK;
+ temp |= PORT_TRANS_SEL_CPT(pipe);
} else {
- temp &= ~LVDS_PIPEB_SELECT;
+ if (pipe == 1) {
+ temp |= LVDS_PIPEB_SELECT;
+ } else {
+ temp &= ~LVDS_PIPEB_SELECT;
+ }
}
+
/* set the corresponsding LVDS_BORDER bit */
temp |= dev_priv->lvds_border_bits;
/* Set the B0-B3 data pairs corresponding to whether we're going to
@@ -129,8 +132,11 @@ static void intel_pre_pll_enable_lvds(struct intel_encoder
*encoder)
* appropriately here, but we need to look more thoroughly into how
* panels behave in the two modes.
*/
- /* set the dithering flag on LVDS as needed */
- if (INTEL_INFO(dev)->gen >= 4) {
+
+ /* Set the dithering flag on LVDS as needed, note that there is no
+ * special lvds dither control bit on pch-split platforms, dithering is
+ * only controlled through the PIPECONF reg. */
+ if (INTEL_INFO(dev)->gen == 4) {
if (dev_priv->lvds_dither)
temp |= LVDS_ENABLE_DITHER;
else
--
1.7.11.7
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
