On Wed, May 08, 2019 at 12:46:09PM +0200, Maarten Lankhorst wrote:
> Op 25-04-2019 om 18:29 schreef Ville Syrjala:
> > From: Ville Syrjälä <ville.syrj...@linux.intel.com>
> >
> > On HSW the pipe A panel fitter lives inside the display power well,
> > and the input MUX for the EDP transcoder needs to be configured
> > appropriately to route the data through the power well as needed.
> > Changing the MUX setting is not allowed while the pipe is active,
> > so we need to force a full modeset whenever we need to change it.
> >
> > Currently we may end up doing a fastset which won't change the
> > MUX settings, but it will drop the power well reference, and that
> > kills the pipe.
> >
> > Cc: sta...@vger.kernel.org
> > Cc: Hans de Goede <hdego...@redhat.com>
> > Cc: Maarten Lankhorst <maarten.lankho...@linux.intel.com>
> > Fixes: d19f958db23c ("drm/i915: Enable fastset for non-boot modesets.")
> > Signed-off-by: Ville Syrjälä <ville.syrj...@linux.intel.com>
> > ---
> > drivers/gpu/drm/i915/intel_display.c | 9 +++++++++
> > drivers/gpu/drm/i915/intel_pipe_crc.c | 13 ++++++++++---
> > 2 files changed, 19 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_display.c
> > b/drivers/gpu/drm/i915/intel_display.c
> > index c67f165b466c..691c9a929164 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -12133,6 +12133,7 @@ intel_pipe_config_compare(struct drm_i915_private
> > *dev_priv,
> > struct intel_crtc_state *pipe_config,
> > bool adjust)
> > {
> > + struct intel_crtc *crtc = to_intel_crtc(current_config->base.crtc);
> > bool ret = true;
> > bool fixup_inherited = adjust &&
> > (current_config->base.mode.private_flags &
> > I915_MODE_FLAG_INHERITED) &&
> > @@ -12354,6 +12355,14 @@ intel_pipe_config_compare(struct drm_i915_private
> > *dev_priv,
> > PIPE_CONF_CHECK_X(gmch_pfit.pgm_ratios);
> > PIPE_CONF_CHECK_X(gmch_pfit.lvds_border_bits);
> >
> > + /*
> > + * Changing the EDP transcoder input mux
> > + * (A_ONOFF vs. A_ON) requires a full modeset.
> > + */
> > + if (IS_HASWELL(dev_priv) && crtc->pipe == PIPE_A &&
> > + current_config->cpu_transcoder == TRANSCODER_EDP)
> > + PIPE_CONF_CHECK_BOOL(pch_pfit.enabled);
>
> I guess it depends if we want to make it a blocker or not..
>
> > +
> > if (!adjust) {
> > PIPE_CONF_CHECK_I(pipe_src_w);
> > PIPE_CONF_CHECK_I(pipe_src_h);
> > diff --git a/drivers/gpu/drm/i915/intel_pipe_crc.c
> > b/drivers/gpu/drm/i915/intel_pipe_crc.c
> > index e94b5b1bc1b7..e7c7be4911c1 100644
> > --- a/drivers/gpu/drm/i915/intel_pipe_crc.c
> > +++ b/drivers/gpu/drm/i915/intel_pipe_crc.c
> > @@ -311,10 +311,17 @@ intel_crtc_crc_setup_workarounds(struct intel_crtc
> > *crtc, bool enable)
> > pipe_config->base.mode_changed = pipe_config->has_psr;
> > pipe_config->crc_enabled = enable;
> >
> > - if (IS_HASWELL(dev_priv) && crtc->pipe == PIPE_A) {
> > + if (IS_HASWELL(dev_priv) &&
> > + pipe_config->base.active && crtc->pipe == PIPE_A &&
> > + pipe_config->cpu_transcoder == TRANSCODER_EDP) {
> > + bool old_need_power_well = pipe_config->pch_pfit.enabled ||
> > + pipe_config->pch_pfit.force_thru;
> > + bool new_need_power_well = pipe_config->pch_pfit.enabled ||
> > + enable;
> > +
> > pipe_config->pch_pfit.force_thru = enable;
> > - if (pipe_config->cpu_transcoder == TRANSCODER_EDP &&
> > - pipe_config->pch_pfit.enabled != enable)
> > +
> > + if (old_need_power_well != new_need_power_well)
> > pipe_config->base.connectors_changed = true;
>
> Could we get rid of this logic and set mode_changed instead?
>
> Ah, I see that is done in 2/2, much less surprises then. :)
Yeah, wanted to keep the fix itself minimal for backporting.
>
> In that case, for both:
>
> Reviewed-by: Maarten Lankhorst <maarten.lankho...@linux.intel.com>
Thanks. Series pushed.
--
Ville Syrjälä
Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
