On Wed, Mar 04, 2020 at 09:56:28PM -0800, Dixit, Ashutosh wrote:
On Wed, 04 Mar 2020 00:52:34 -0800, Lionel Landwerlin wrote:
On 04/03/2020 07:48, Dixit, Ashutosh wrote:
> On Tue, 03 Mar 2020 14:19:05 -0800, Umesh Nerlige Ramappa wrote:
>> From: Lionel Landwerlin <lionel.g.landwer...@intel.com>
>>
>> With the currently available parameters for the i915-perf stream,
>> there are still situations that are not well covered :
>>
>> If an application opens the stream with polling disable or at very low
>> frequency and OA interrupt enabled, no data will be available even
>> though somewhere between nothing and half of the OA buffer worth of
>> data might have landed in memory.
>>
>> To solve this issue we have a new flush ioctl on the perf stream that
>> forces the i915-perf driver to look at the state of the buffer when
>> called and makes any data available through both poll() & read() type
>> syscalls.
>>
>> v2: Version the ioctl (Joonas)
>> v3: Rebase (Umesh)
>>
>> Signed-off-by: Lionel Landwerlin <lionel.g.landwer...@intel.com>
>> Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.rama...@intel.com>
> [snip]
>
>> +/**
>> + * i915_perf_flush_data - handle `I915_PERF_IOCTL_FLUSH_DATA` ioctl
>> + * @stream: An enabled i915 perf stream
>> + *
>> + * The intention is to flush all the data available for reading from the OA
>> + * buffer
>> + */
>> +static void i915_perf_flush_data(struct i915_perf_stream *stream)
>> +{
>> + stream->pollin = oa_buffer_check(stream, true);
>> +}
> Since this function doesn't actually wake up any thread (which anyway can
> be done by sending a signal to the blocked thread), is the only purpose of
> this function to update OA buffer head/tail? But in that it is not clear
> why a separate ioctl should be created for this, can't the read() call
> itself call oa_buffer_check() to update the OA buffer head/tail?
>
> Again just trying to minimize uapi changes if possible.
Most applications will call read() after being notified by poll()/select()
that some data is available.
Correct this is the standard non blocking read behavior.
Changing that behavior will break some of the existing perf tests .
I am not suggesting changing that (that standard non blocking read
behavior).
If any data is available, this new ioctl will wake up existing waiters on
poll()/select().
The issue is we are not calling wake_up() in the above function to wake up
any blocked waiters. The ioctl will just update the OA buffer head/tail so
that (a) a subsequent blocking read will not block, or (b) a subsequent non
blocking read will return valid data (not -EAGAIN), or (c) a poll/select
will not block but return immediately saying data is available.
That is why it seems to me the ioctl is not required, updating the OA
buffer head/tail can be done as part of the read() (and the poll/select)
calls themselves.
We will investigate if this can be done and update the patches in the next
revision accordingly. Thanks!
In this case, where we are trying to determine if there is any data in
the oa buffer before the next interrupt has fired, user could call poll
with a reasonable timeout to determine if data is available or not.
That would eliminate the need for the flush ioctl. Thoughts?
Thanks,
Umesh
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
