In case of dual link, we get the TE on slave.
So clear the TE on slave DSI IIR.
If we are operating in TE_GATE mode, after we do
a frame update, the transcoder will send the frame data
to the panel, after it receives a TE. Whereas if we
are operating in NO_GATE mode then the transcoder will
immediately send the frame data to the panel.
We are not dealing with the periodic command mode here.
v2: Pass only relevant masked bits to the handler (Jani)
v3: Fix the check for cmd mode in TE handler function.
v4: Use intel_handle_vblank instead of drm_handle_vblank (Jani)
v3: Use static on handler func (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulka...@intel.com>
Reported-by: kernel test robot <l...@intel.com>
Acked-by: Jani Nikula <jani.nik...@intel.com>
---
drivers/gpu/drm/i915/i915_irq.c | 66 +++++++++++++++++++++++++++++++++
1 file changed, 66 insertions(+)
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 913548addfba..4a1f13425108 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -2237,6 +2237,64 @@ gen8_de_misc_irq_handler(struct drm_i915_private
*dev_priv, u32 iir)
drm_err(&dev_priv->drm, "Unexpected DE Misc interrupt\n");
}
+static void gen11_dsi_te_interrupt_handler(struct drm_i915_private *dev_priv,
+ u32 te_trigger)
+{
+ enum pipe pipe = INVALID_PIPE;
+ enum transcoder dsi_trans;
+ enum port port;
+ u32 val, tmp;
+
+ /*
+ * Incase of dual link, TE comes from DSI_1
+ * this is to check if dual link is enabled
+ */
+ val = I915_READ(TRANS_DDI_FUNC_CTL2(TRANSCODER_DSI_0));
+ val &= PORT_SYNC_MODE_ENABLE;
+
+ /*
+ * if dual link is enabled, then read DSI_0
+ * transcoder registers
+ */
+ port = ((te_trigger & DSI1_TE && val) || (te_trigger & DSI0_TE)) ?
+ PORT_A : PORT_B;
+ dsi_trans = (port == PORT_A) ? TRANSCODER_DSI_0 : TRANSCODER_DSI_1;
+
+ /* Check if DSI configured in command mode */
+ val = I915_READ(DSI_TRANS_FUNC_CONF(dsi_trans));
+ val = val & OP_MODE_MASK;
+
+ if ((val != CMD_MODE_NO_GATE) && (val != CMD_MODE_TE_GATE)) {
+ drm_err(&dev_priv->drm, "DSI trancoder not configured in
command mode\n");
+ return;
+ }
+
+ /* Get PIPE for handling VBLANK event */
+ val = I915_READ(TRANS_DDI_FUNC_CTL(dsi_trans));
+ switch (val & TRANS_DDI_EDP_INPUT_MASK) {
+ case TRANS_DDI_EDP_INPUT_A_ON:
+ pipe = PIPE_A;
+ break;
+ case TRANS_DDI_EDP_INPUT_B_ONOFF:
+ pipe = PIPE_B;
+ break;
+ case TRANS_DDI_EDP_INPUT_C_ONOFF:
+ pipe = PIPE_C;
+ break;
+ default:
+ drm_err(&dev_priv->drm, "Invalid PIPE\n");
+ return;
+ }
+
+ intel_handle_vblank(dev_priv, pipe);
+
+ /* clear TE in dsi IIR */
+ port = (te_trigger & DSI1_TE) ? PORT_B : PORT_A;
+ tmp = I915_READ(DSI_INTR_IDENT_REG(port));
+ I915_WRITE(DSI_INTR_IDENT_REG(port), tmp);
+
+}
+
static irqreturn_t
gen8_de_irq_handler(struct drm_i915_private *dev_priv, u32 master_ctl)
{
@@ -2301,6 +2359,14 @@ gen8_de_irq_handler(struct drm_i915_private *dev_priv,
u32 master_ctl)
found = true;
}
+ if (INTEL_GEN(dev_priv) >= 11) {
+ tmp_mask = iir & (DSI0_TE | DSI1_TE);
+ if (tmp_mask) {
+
gen11_dsi_te_interrupt_handler(dev_priv, tmp_mask);
+ found = true;
+ }
+ }
+
if (!found)
drm_err(&dev_priv->drm,
"Unexpected DE Port interrupt\n");
--
2.21.0.5.gaeb582a
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
