On Wed, Jan 19, 2022 at 05:17:05PM +0200, Jani Nikula wrote:
> On Wed, 19 Jan 2022, Ville Syrjala <ville.syrj...@linux.intel.com> wrote:
> > From: Ville Syrjälä <ville.syrj...@linux.intel.com>
> >
> > dg2_ddi_pre_enable_dp() has outlived its usefulness so eliminate
> > it.
> >
> > The one thing that tgl_ddi_pre_enable_dp() is missing that we
> > need is intel_ddi_config_transcoder_dp2(). So we'll bring that
> > over.
> >
> > tgl_ddi_pre_enable_dp() does also have a few things that
> > dg2_ddi_pre_enable_dp() didn't have:
> > - icl_program_mg_dp_mode() -> nop due to intel_phy_is_tc()==false on DG2
> > - intel_ddi_power_up_lanes() -> nop due to intel_phy_is_combo()==false on
> > DG2
> > - intel_ddi_mso_configure() -> only matters for MSO panels
> >
> > Another slight difference is that dg2_ddi_pre_enable_dp() was
> > missing a bigjoiner check around intel_dsc_enable(), which
> > tgl_ddi_pre_enable_dp() does have.
Thanks Ville for this patch, I was just comparing differences between
dg2_pre_enable_dp and tgl_pre_enable_dp
in regards to a bug and there is totally no need for two functions with the
checks you have here.
For the bigjoiner check aroind intel_dsc_enable(), I think the function
intel_dsc_dp_pps_write(encoder, crtc_state);
also needs to be moved into that check.
And then this functions needs to be called from icl_ddi_bigjoiner_pre_enable()
where we call intel_dsc_enable
With that:
Reviewed-by: Manasi Navare <manasi.d.nav...@intel.com>
Manasi
>
> Reviewed-by: Jani Nikula <jani.nik...@intel.com>
>
> The modeset step bspec references could use a cleanup too. If they
> aren't stable number&letter combos for *one* platform, let alone many,
> we should probably just remove them.
>
> >
> > Signed-off-by: Ville Syrjälä <ville.syrj...@linux.intel.com>
> > ---
> > drivers/gpu/drm/i915/display/intel_ddi.c | 117 +----------------------
> > 1 file changed, 4 insertions(+), 113 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> > b/drivers/gpu/drm/i915/display/intel_ddi.c
> > index 4e93eac926a5..2f20abc5122d 100644
> > --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> > +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> > @@ -2289,116 +2289,6 @@ static void intel_ddi_mso_configure(const struct
> > intel_crtc_state *crtc_state)
> > OVERLAP_PIXELS_MASK, dss1);
> > }
> >
> > -static void dg2_ddi_pre_enable_dp(struct intel_atomic_state *state,
> > - struct intel_encoder *encoder,
> > - const struct intel_crtc_state *crtc_state,
> > - const struct drm_connector_state *conn_state)
> > -{
> > - struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
> > - struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> > - struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
> > - bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
> > -
> > - intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
> > - crtc_state->lane_count);
> > -
> > - /*
> > - * We only configure what the register value will be here. Actual
> > - * enabling happens during link training farther down.
> > - */
> > - intel_ddi_init_dp_buf_reg(encoder, crtc_state);
> > -
> > - /*
> > - * 1. Enable Power Wells
> > - *
> > - * This was handled at the beginning of intel_atomic_commit_tail(),
> > - * before we called down into this function.
> > - */
> > -
> > - /* 2. Enable Panel Power if PPS is required */
> > - intel_pps_on(intel_dp);
> > -
> > - /*
> > - * 3. Enable the port PLL.
> > - */
> > - intel_ddi_enable_clock(encoder, crtc_state);
> > -
> > - /* 4. Enable IO power */
> > - if (!intel_tc_port_in_tbt_alt_mode(dig_port))
> > - dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
> > -
> > dig_port->ddi_io_power_domain);
> > -
> > - /*
> > - * 5. The rest of the below are substeps under the bspec's "Enable and
> > - * Train Display Port" step. Note that steps that are specific to
> > - * MST will be handled by intel_mst_pre_enable_dp() before/after it
> > - * calls into this function. Also intel_mst_pre_enable_dp() only calls
> > - * us when active_mst_links==0, so any steps designated for "single
> > - * stream or multi-stream master transcoder" can just be performed
> > - * unconditionally here.
> > - */
> > -
> > - /*
> > - * 5.a Configure Transcoder Clock Select to direct the Port clock to the
> > - * Transcoder.
> > - */
> > - intel_ddi_enable_pipe_clock(encoder, crtc_state);
> > -
> > - /* 5.b Configure transcoder for DP 2.0 128b/132b */
> > - intel_ddi_config_transcoder_dp2(encoder, crtc_state);
> > -
> > - /*
> > - * 5.c Configure TRANS_DDI_FUNC_CTL DDI Select, DDI Mode Select & MST
> > - * Transport Select
> > - */
> > - intel_ddi_config_transcoder_func(encoder, crtc_state);
> > -
> > - /*
> > - * 5.d Configure & enable DP_TP_CTL with link training pattern 1
> > - * selected
> > - *
> > - * This will be handled by the intel_dp_start_link_train() farther
> > - * down this function.
> > - */
> > -
> > - /* 5.e Configure voltage swing and related IO settings */
> > - encoder->set_signal_levels(encoder, crtc_state);
> > -
> > - if (!is_mst)
> > - intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
> > -
> > - intel_dp_configure_protocol_converter(intel_dp, crtc_state);
> > - intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
> > - /*
> > - * DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
> > - * in the FEC_CONFIGURATION register to 1 before initiating link
> > - * training
> > - */
> > - intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
> > - intel_dp_check_frl_training(intel_dp);
> > - intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
> > -
> > - /*
> > - * 5.h Follow DisplayPort specification training sequence (see notes for
> > - * failure handling)
> > - * 5.i If DisplayPort multi-stream - Set DP_TP_CTL link training to Idle
> > - * Pattern, wait for 5 idle patterns (DP_TP_STATUS Min_Idles_Sent)
> > - * (timeout after 800 us)
> > - */
> > - intel_dp_start_link_train(intel_dp, crtc_state);
> > -
> > - /* 5.j Set DP_TP_CTL link training to Normal */
> > - if (!is_trans_port_sync_mode(crtc_state))
> > - intel_dp_stop_link_train(intel_dp, crtc_state);
> > -
> > - /* 5.k Configure and enable FEC if needed */
> > - intel_ddi_enable_fec(encoder, crtc_state);
> > -
> > - intel_dsc_dp_pps_write(encoder, crtc_state);
> > -
> > - intel_dsc_enable(crtc_state);
> > -}
> > -
> > static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
> > struct intel_encoder *encoder,
> > const struct intel_crtc_state *crtc_state,
> > @@ -2472,6 +2362,9 @@ static void tgl_ddi_pre_enable_dp(struct
> > intel_atomic_state *state,
> > */
> > intel_ddi_enable_pipe_clock(encoder, crtc_state);
> >
> > + if (HAS_DP20(dev_priv))
> > + intel_ddi_config_transcoder_dp2(encoder, crtc_state);
> > +
> > /*
> > * 7.b Configure TRANS_DDI_FUNC_CTL DDI Select, DDI Mode Select & MST
> > * Transport Select
> > @@ -2612,9 +2505,7 @@ static void intel_ddi_pre_enable_dp(struct
> > intel_atomic_state *state,
> > {
> > struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> >
> > - if (IS_DG2(dev_priv))
> > - dg2_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
> > - else if (DISPLAY_VER(dev_priv) >= 12)
> > + if (DISPLAY_VER(dev_priv) >= 12)
> > tgl_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
> > else
> > hsw_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
>
> --
> Jani Nikula, Intel Open Source Graphics Center
