Move the DPCD read to the top and check for an interrupt from the sink to catch Displayport automated testing requests necessary to support Displayport compliance testing. The checks for active connectors and link status are moved below the check for the interrupt.
The main reason for doing this is to make sure that a test request isn't missed. Checking for the status of the encoder/crtc isn't necessary for some test cases (AUX channel tests are one example) and without moving the check for the interrupt, these tests may not execute if one of those checks fails. Additionally, if reading the DPCD fails, regardless of whether or not testing is happening, there's no way to train the link since configurations and status can't be read, nor can link training parameters be written. V1: - This is the second part of the single-patch split previously mentioned. V2: - Remerge the two split patches into one and update the commit message accordingly. - Replace the SW connected status check with a HW HPD pin status check - Adds a new function that examines the status of the HPD pin to determine if a sink device is connected V3: - CLean up of the patch merge from previous split - Updated the commit message Signed-off-by: Todd Previte <tprev...@gmail.com> --- drivers/gpu/drm/i915/intel_dp.c | 33 +++++++++++++++------------------ 1 file changed, 15 insertions(+), 18 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c index 263eff3..9c38986 100644 --- a/drivers/gpu/drm/i915/intel_dp.c +++ b/drivers/gpu/drm/i915/intel_dp.c @@ -4119,24 +4119,8 @@ intel_dp_check_link_status(struct intel_dp *intel_dp) WARN_ON(!drm_modeset_is_locked(&dev->mode_config.connection_mutex)); - if (!intel_encoder->connectors_active) - return; - - if (WARN_ON(!intel_encoder->base.crtc)) - return; - - if (!to_intel_crtc(intel_encoder->base.crtc)->active) - return; - - /* Try to read receiver status if the link appears to be up */ - if (!intel_dp_get_link_status(intel_dp, link_status)) { - return; - } - - /* Now read the DPCD to see if it's actually running */ - if (!intel_dp_get_dpcd(intel_dp)) { + if (!intel_dp_get_dpcd(intel_dp)) return; - } /* Try to read the source of the interrupt */ if (intel_dp->dpcd[DP_DPCD_REV] >= 0x11 && @@ -4145,13 +4129,26 @@ intel_dp_check_link_status(struct intel_dp *intel_dp) drm_dp_dpcd_writeb(&intel_dp->aux, DP_DEVICE_SERVICE_IRQ_VECTOR, sink_irq_vector); - if (sink_irq_vector & DP_AUTOMATED_TEST_REQUEST) intel_dp_handle_test_request(intel_dp); if (sink_irq_vector & (DP_CP_IRQ | DP_SINK_SPECIFIC_IRQ)) DRM_DEBUG_DRIVER("CP or sink specific irq unhandled\n"); } + if (!intel_encoder->connectors_active) + return; + + if (WARN_ON(!intel_encoder->base.crtc)) + return; + + if (!to_intel_crtc(intel_encoder->base.crtc)->active) + return; + + /* Try to read receiver status if the link appears to be up */ + if (!intel_dp_get_link_status(intel_dp, link_status)) { + return; + } + if (!drm_dp_channel_eq_ok(link_status, intel_dp->lane_count)) { DRM_DEBUG_KMS("%s: channel EQ not ok, retraining\n", intel_encoder->base.name); -- 1.9.1 _______________________________________________ Intel-gfx mailing list Intel-gfx@lists.freedesktop.org http://lists.freedesktop.org/mailman/listinfo/intel-gfx