On 7/18/2015 5:17 AM, Imre Deak wrote:
On Fri, 2015-07-17 at 13:47 +0530, Sonika Jindal wrote:
As per bspec, on BXT A0/A1, sw needs to activate DDIA HPD logic
and interrupts to check the external panel connection and DDIC HPD
logic for edp panel.
v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
Signed-off-by: Sonika Jindal <sonika.jin...@intel.com>
---
drivers/gpu/drm/i915/intel_ddi.c | 10 +++++++++-
drivers/gpu/drm/i915/intel_hdmi.c | 9 ++++++++-
2 files changed, 17 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index e2c6f73..777e3a3 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -3225,7 +3225,15 @@ void intel_ddi_init(struct drm_device *dev, enum port
port)
goto err;
intel_dig_port->hpd_pulse = intel_dp_hpd_pulse;
- dev_priv->hotplug.irq_port[port] = intel_dig_port;
+ /*
+ * On BXT A0/A1, sw needs to activate DDIA HPD logic and
+ * interrupts to check the external panel connection.
+ */
+ if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0)
+ && port == PORT_B)
+ dev_priv->hotplug.irq_port[PORT_A] = intel_dig_port;
This happens to work but is confusing. irq_port[PORT_A] will be set here
already and the above will simply overwrite it without explanation. I
would also handle the port == PORT_A case and not set irq_port for it.
The same swapping for hpd_pin is missing from intel_dp_init_connector().
+ else
+ dev_priv->hotplug.irq_port[port] = intel_dig_port;
}
/* In theory we don't need the encoder->type check, but leave it just in
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c
b/drivers/gpu/drm/i915/intel_hdmi.c
index 70bad5b..94fa716 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1973,7 +1973,14 @@ void intel_hdmi_init_connector(struct intel_digital_port
*intel_dig_port,
intel_hdmi->ddc_bus = GMBUS_PIN_1_BXT;
else
intel_hdmi->ddc_bus = GMBUS_PIN_DPB;
- intel_encoder->hpd_pin = HPD_PORT_B;
+ /*
+ * On BXT A0/A1, sw needs to activate DDIA HPD logic and
+ * interrupts to check the external panel connection.
+ */
+ if (IS_BROXTON(dev_priv) && (INTEL_REVID(dev) < BXT_REVID_B0))
+ intel_encoder->hpd_pin = HPD_PORT_A;
+ else
+ intel_encoder->hpd_pin = HPD_PORT_B;
break;
case PORT_C:
if (IS_BROXTON(dev_priv))
As I earlier pointed out with the above approach, you need to add
support for HPD events on the HPD_PORT_A pin. If you look at the
for_each_hpd_pin() macro and intel_hpd_irq_handler()/is_dig_port you'll
notice that any interrupt event on the HPD_PORT_A pin will be ignored
now.
Hmm :(. For now, we can fix for_each_hpd_pin and add a check in
intel_hpd_pin_to_port to return PORT_B for pin 0 if A0/A1. Then we can
skip the check in intel_ddi_init. But this again will look very confusing.
So two options:
1. We move back to the older approach where we just use another hpd
ports array in i915_irq.c
2. Go with current approach.
I feel option 1 is more clean and less prone to further issues.
What do you suggest?
Regards,
Sonika
--Imre
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
