On Thu, Jun 11, 2020 at 10:54:45AM +0800, Zhangfei Gao wrote: > On 2020/6/10 上午12:49, Bjorn Helgaas wrote: > > On Tue, Jun 09, 2020 at 11:15:06AM +0200, Arnd Bergmann wrote: > > > On Tue, Jun 9, 2020 at 6:02 AM Zhangfei Gao <zhangfei....@linaro.org> > > > wrote: > > > > On 2020/6/9 上午12:41, Bjorn Helgaas wrote: > > > > > On Mon, Jun 08, 2020 at 10:54:15AM +0800, Zhangfei Gao wrote: > > > > > > On 2020/6/6 上午7:19, Bjorn Helgaas wrote: > > > > > > > > +++ b/drivers/iommu/iommu.c > > > > > > > > @@ -2418,6 +2418,10 @@ int iommu_fwspec_init(struct device > > > > > > > > *dev, struct > > > > > > > > fwnode_handle *iommu_fwnode, > > > > > > > > fwspec->iommu_fwnode = iommu_fwnode; > > > > > > > > fwspec->ops = ops; > > > > > > > > dev_iommu_fwspec_set(dev, fwspec); > > > > > > > > + > > > > > > > > + if (dev_is_pci(dev)) > > > > > > > > + pci_fixup_device(pci_fixup_final, > > > > > > > > to_pci_dev(dev)); > > > > > > > > + > > > > > > > > > > > > > > > > Then pci_fixup_final will be called twice, the first in > > > > > > > > pci_bus_add_device. > > > > > > > > Here in iommu_fwspec_init is the second time, specifically for > > > > > > > > iommu_fwspec. > > > > > > > > Will send this when 5.8-rc1 is open. > > > > > > > Wait, this whole fixup approach seems wrong to me. No matter how > > > > > > > you > > > > > > > do the fixup, it's still a fixup, which means it requires ongoing > > > > > > > maintenance. Surely we don't want to have to add the > > > > > > > Vendor/Device ID > > > > > > > for every new AMBA device that comes along, do we? > > > > > > > > > > > > > Here the fake pci device has standard PCI cfg space, but physical > > > > > > implementation is base on AMBA > > > > > > They can provide pasid feature. > > > > > > However, > > > > > > 1, does not support tlp since they are not real pci devices. > > > > > > 2. does not support pri, instead support stall (provided by smmu) > > > > > > And stall is not a pci feature, so it is not described in struct > > > > > > pci_dev, > > > > > > but in struct iommu_fwspec. > > > > > > So we use this fixup to tell pci system that the devices can > > > > > > support stall, > > > > > > and hereby support pasid. > > > > > This did not answer my question. Are you proposing that we update a > > > > > quirk every time a new AMBA device is released? I don't think that > > > > > would be a good model. > > > > Yes, you are right, but we do not have any better idea yet. > > > > Currently we have three fake pci devices, which support stall and pasid. > > > > We have to let pci system know the device can support pasid, because of > > > > stall feature, though not support pri. > > > > Do you have any other ideas? > > > It sounds like the best way would be to allocate a PCI capability for it, > > > so > > > detection can be done through config space, at least in future devices, > > > or possibly after a firmware update if the config space in your system > > > is controlled by firmware somewhere. Once there is a proper mechanism > > > to do this, using fixups to detect the early devices that don't use that > > > should be uncontroversial. I have no idea what the process or timeline > > > is to add new capabilities into the PCIe specification, or if this one > > > would be acceptable to the PCI SIG at all. > > That sounds like a possibility. The spec already defines a > > Vendor-Specific Extended Capability (PCIe r5.0, sec 7.9.5) that might > > be a candidate. > Will investigate this, thanks Bjorn
FWIW, there's also a Vendor-Specific Capability that can appear in the first 256 bytes of config space (the Vendor-Specific Extended Capability must appear in the "Extended Configuration Space" from 0x100-0xfff). > > > If detection cannot be done through PCI config space, the next best > > > alternative is to pass auxiliary data through firmware. On DT based > > > machines, you can list non-hotpluggable PCIe devices and add custom > > > properties that could be read during device enumeration. I assume > > > ACPI has something similar, but I have not done that. > Yes, thanks Arnd > > ACPI has _DSM (ACPI v6.3, sec 9.1.1), which might be a candidate. I > > like this better than a PCI capability because the property you need > > to expose is not a PCI property. > _DSM may not workable, since it is working in runtime. > We need stall information in init stage, neither too early (after allocation > of iommu_fwspec) > nor too late (before arm_smmu_add_device ). I'm not aware of a restriction on when _DSM can be evaluated. I'm looking at ACPI v6.3, sec 9.1.1. Are you seeing something different? > By the way, It would be a long time if we need modify either pcie > spec or acpi spec. Can we use pci_fixup_device in iommu_fwspec_init > first, it is relatively simple and meet the requirement of platform > device using pasid, and they are already in product. Neither the PCI Vendor-Specific Capability nor the ACPI _DSM requires a spec change. Both can be completely vendor-defined. _______________________________________________ iommu mailing list iommu@lists.linux-foundation.org https://lists.linuxfoundation.org/mailman/listinfo/iommu
