Back in the 1990s, I built an 8' tall doubly balanced PVC loop that had excellent characteristics. It was doubly balanced (two identical loop windings emanating from the center ground point, and was tapped at one turn out on each side, feeding a balanced toroidal balun. The loop did require amplification off the toroid. I logged KNX-1070-CA on it one night from Blacksburg, VA. This loop had amazing nulls. The tiniest movement had a large effect.
That was in an apartment environment, and the loop was only usable late at night after people had gone to bed and turned off their appliances. Today in an apartment environment, that loop is worthless. There is so much more man made RFI now than then that it is never quiet. Computers, dimmers, smart appliances, CFLs, etc. make the noise level unbearable. The only way I can DX now in a similar environment is with an 8' tall shielded loop enclosed in thin wall metal conduit. The Q of this loop is much lower, and the nulls quite poor - yet, it conquers most of the noise. Oh, for a little house on a hilltop somewhere with no neighbors for 5 miles. LOL. --- On Mon, 4/13/09, [email protected] <[email protected]> wrote: From: [email protected] <[email protected]> Subject: [IRCA] Monster PVC-Frame Passive Loops To: [email protected], [email protected] Date: Monday, April 13, 2009, 9:23 AM Hello All, The annual "March Madness" antenna project here this year was to construct a series of tuned passive loops, using ultra-cheap PVC tubing and fittings. Loops of 18", 2', 3', 4', 5', 6' and 7.5' (side dimensions) were assembled, using PVC diameters suitable to support each size without any sagging. One of the primary design considerations was to isolate the loops from the support structures as much as possible, to provide clean electromagnetic reception patterns. Perfect symmetry of the coils was also an important objective, with equally-spaced wire slots cut in each of four frame tubes, and the tuning capacitor located exactly at the loop ends, with the far end of the loop routed through a short PVC tube to the capacitor. These steps seem to have provided maximum sensitivity and nulling ability for each loop size. Lightweight, rugged, waterproof PVC was found to be an ideal frame material for tuned passive loops, and of course, it is also ultra-cheap (even in the larger sizes). The 7.5 foot (side) monster loop frame cost all of $35 to build, and the cost of the "tabletop" 18-inch model frame was about $7. The 7.5 foot (10 foot diagonal) PVC loop does require some serious real estate for construction, however, and is certainly not recommended if you have a shaky relationship with any of your neighbors :>) Photos of the 18", 2' and 7.5' PVC loops have been uploaded to the Ultralightdx Yahoo group site, and are available upon request. An article containing full construction details for these new PVC-frame loops should be written shortly, which hopefully will provide a new, inexpensive option for boosting the DXing ability of any receiver. 73, Gary DeBock **************Why pay full price? Check out this month's deals on the new AOL Shopping. (http://shopping.aol.com/?ncid=emlcntinstor00000001) _______________________________________________ IRCA mailing list [email protected] http://montreal.kotalampi.com/mailman/listinfo/irca Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers For more information: http://www.ircaonline.org To Post a message: [email protected] _______________________________________________ IRCA mailing list [email protected] http://montreal.kotalampi.com/mailman/listinfo/irca Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers For more information: http://www.ircaonline.org To Post a message: [email protected]
