Thanks that fixes the errors I was having but creates another. On my first
tuner, all I get is static/snow kind of like it is using the wrong tuner.
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.13-1.1526_FC4smp SMP 686 REGPARM 4KSTACKS gcc-4.0
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 58
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8233154
tveeprom: tuner = <unknown> (idx = 99, type = 1267182958)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = TDA9850 (type = 3)
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
cx25840 0-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
tuner: type too large 1267182958 >= 68
tuner: tuner type not set
ivtv0: Initialized WinTV PVR 150, card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 18 (level, low) -> IRQ 185
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
tveeprom: The eeprom says no radio is present, but the tuner type
tveeprom: indicates otherwise. I will assume that radio is present.
tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8200381
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3410D (type = 5)
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv1: Create encoder radio stream
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #1
ivtv1: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================
lirc_dev: IR Remote Control driver registered, at major 61
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
cx2388x v4l2 driver version 0.0.5 loaded
lirc_i2c: chip found @ 0x71 (Hauppauge IR (PVR150))
ivtv0: i2c attach to card #0 ok [client=Hauppauge IR (PVR150), addr=71]
lirc_dev: lirc_register_plugin: sample_rate: 10
>>> [EMAIL PROTECTED] 10/14/05 2:50 AM >>>
If you use the kernel version of tveeprom all your problems will go away.
On 10/13/05, Scott Starkey <[EMAIL PROTECTED]> wrote:
> I have a setup with two PVR 150's. 1 MCE and 1 Retail w/remote. I'm using
> the 4.0 drivers compiled from source and they work great until I add the
> lines in Modprobe.conf for lirc. Please let me know if I need to include
> more info. Thanks!
>
> Scott
>
> Kernel Version
> 2.6.13-1.1526_FC4smp
>
>
> modprobe.conf
>
> alias eth0 3c59x
> alias scsi_hostadapter ata_piix
> alias snd-card-0 snd-hda-intel
> alias char-major-61 lirc_i2c
> options snd-card-0 index=0
> options snd-hda-intel index=0
> remove snd-hda-intel { /usr/sbin/alsactl store 0 >/dev/null 2>&1 || : ; };
> /sbin/modprobe -r --ignore-remove snd-hda-intel
> alias usb-controller ehci-hcd
> alias usb-controller1 uhci-hcd
> # nvidia kernel module
> alias char-major-195 nvidia-1_0-7676
> alias nvidia nvidia-1_0-7676
> # ivtv (PVR-150MCE)
> alias char-major-81 ivtv
> alias char-major-81-0 ivtv
> alias char-major-81-1 ivtv
> install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c
>
>
> dmesg with LIRC in Modprobe.conf
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.0 (tagged release) loading
> ivtv: Linux version: 2.6.13-1.1526_FC4smp SMP 686 REGPARM 4KSTACKS gcc-4.0
> ivtv: In case of problems please include the debug info
> ivtv: between the START INIT IVTV and END INIT IVTV lines when
> ivtv: mailing the ivtv-devel mailinglist.
> ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
> ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 58
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom: ivtv version
> tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8233154
> tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio processor = CX25841 (type = 23)
> tveeprom: decoder processor = CX25841 (type = 1c)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> cx25840 0-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> ivtv0: loading /lib/modules/ivtv-fw-enc.bin
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total)
> tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
> ivtv0: Initialized WinTV PVR 150, card #0
> ivtv: ====================== NEXT CARD ======================
> ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
> ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 18 (level, low) -> IRQ 185
> ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom: The eeprom says no radio is present, but the tuner type 68
> tveeprom: indicates otherwise. I will assume that radio is present.
> tveeprom: ivtv version
> tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8200381
> tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio processor = CX25843 (type = 25)
> tveeprom: decoder processor = CX25843 (type = 1e)
> ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
> ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
> cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
> cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
> ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
> ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
> tda9885/6/7: (ivtv) chip found @ 0x86
> ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
> ivtv1: loading /lib/modules/ivtv-fw-enc.bin
> ivtv1: Encoder revision: 0x02050032
> ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
> ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
> ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total)
> ivtv1: Create encoder radio stream
> tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #1
> ivtv1: Initialized WinTV PVR 150, card #1
> ivtv: ==================== END INIT IVTV ====================
> lirc_dev: IR Remote Control driver registered, at major 61
> bttv: disagrees about version of symbol tveeprom_hauppauge_analog
> bttv: Unknown symbol tveeprom_hauppauge_analog
> cx88xx: disagrees about version of symbol tveeprom_hauppauge_analog
> cx88xx: Unknown symbol tveeprom_hauppauge_analog
> cx8800: Unknown symbol cx88_reset
> cx8800: Unknown symbol cx88_call_i2c_clients
> cx8800: Unknown symbol cx88_wakeup
> cx8800: Unknown symbol cx88_risc_stopper
> cx8800: Unknown symbol cx88_print_irqbits
> cx8800: Unknown symbol cx88_set_scale
> cx8800: Unknown symbol cx88_shutdown
> cx8800: Unknown symbol cx88_vdev_init
> cx8800: Unknown symbol cx88_core_put
> cx8800: Unknown symbol cx88_audio_thread
> cx8800: Unknown symbol cx88_core_irq
> cx8800: Unknown symbol cx88_core_get
> cx8800: Unknown symbol cx88_get_stereo
> cx8800: Unknown symbol cx88_set_tvnorm
> cx8800: Unknown symbol cx88_risc_buffer
> cx8800: Unknown symbol cx88_set_stereo
> cx8800: Unknown symbol cx88_sram_channels
> cx8800: Unknown symbol cx88_set_tvaudio
> cx8800: Unknown symbol cx88_sram_channel_dump
> cx8800: Unknown symbol cx88_sram_channel_setup
> cx8800: Unknown symbol cx88_print_ioctl
> cx8800: Unknown symbol cx88_free_buffer
> cx8800: Unknown symbol cx88_boards
> cx8800: Unknown symbol cx88_newstation
> lirc_i2c: chip found @ 0x71 (Hauppauge IR (PVR150))
> ivtv0: i2c attach to card #0 ok [client=Hauppauge IR (PVR150), addr=71]
> lirc_dev: lirc_register_plugin: sample_rate: 10
>
> dmesg without LIRC in modprobe.conf
>
> Linux video capture interface: v1.00
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.0 (tagged release) loading
> ivtv: Linux version: 2.6.13-1.1526_FC4smp SMP 686 REGPARM 4KSTACKS gcc-4.0
> ivtv: In case of problems please include the debug info
> ivtv: between the START INIT IVTV and END INIT IVTV lines when
> ivtv: mailing the ivtv-devel mailinglist.
> ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
> ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 58
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom: ivtv version
> tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8233154
> tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio processor = CX25841 (type = 23)
> tveeprom: decoder processor = CX25841 (type = 1c)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> cx25840 0-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> ivtv0: loading /lib/modules/ivtv-fw-enc.bin
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total)
> tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
> ivtv0: Initialized WinTV PVR 150, card #0
> ivtv: ====================== NEXT CARD ======================
> ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
> ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 18 (level, low) -> IRQ 185
> ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
> tveeprom: The eeprom says no radio is present, but the tuner type 68
> tveeprom: indicates otherwise. I will assume that radio is present.
> tveeprom: ivtv version
> tveeprom: Hauppauge: model = 26552, rev = C268, serial# = 8200381
> tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio processor = CX25843 (type = 25)
> tveeprom: decoder processor = CX25843 (type = 1e)
> ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
> ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
> cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
> cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes)
> ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
> ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
> tda9885/6/7: (ivtv) chip found @ 0x86
> ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
> ivtv1: loading /lib/modules/ivtv-fw-enc.bin
> ivtv1: Encoder revision: 0x02050032
> ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
> ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
> ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total)
> ivtv1: Create encoder radio stream
> tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #1
> ivtv1: Initialized WinTV PVR 150, card #1
> ivtv: ==================== END INIT IVTV ====================
>
> This e-mail, including attachments, is covered by the Electronic
> Communications Privacy Act, 18 U.S.C. 2510-2521, is confidential,
> and may be legally privileged. If you are not the intended recipient,
> you are hereby notified that any retention, dissemination,
> distribution, or copying of this communication is strictly prohibited.
>
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
>
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
This e-mail, including attachments, is covered by the Electronic
Communications Privacy Act, 18 U.S.C. 2510-2521, is confidential,
and may be legally privileged. If you are not the intended recipient,
you are hereby notified that any retention, dissemination,
distribution, or copying of this communication is strictly prohibited.
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
