I think I have covered most of the suggestions posted in this thread:
1) Renamed all instances of tuner.ko, msp3400.ko, and tda9887.ko to prevent these kernel version from being loaded. This appears to have made no difference one way or the other. I tried renaming each module one at a time, and making the corresponding alias entry in modprobe, but to no avail.
2) Upgraded to ivtv driver 0.4.0.
3) Updated my firmware to version 0x02050032. This got rid of the warning I previously had.
4) Removed all instructions from modprobe.conf except the ones that appear to be necessary, as shown below. After taking the actions of step 1) above, it became necessary to add the ivtv aliases or the modules could not be loaded.
5) Installed the mkinitrd changes and recreated my boot image. Can anyone explain why this is necessary for the PVR-500? Based on Jarod's site, it appears this change is necessary for the PVR-350 since it has on-board TV-out and piping X over that requires some modules be made available in the boot image?
After doing all this, I am still unable to get anything but static on /dev/video0. There are 2 odd messages in the dmesg output below that I am unable to solve.
I'm really starting to wonder if there is some sort of hardware failure going on here. My next step is to move the PVR-500 to my windows machine to check it out for some sort of hardware issue...unless someone has a better suggestion :(
Larry
modprobe.conf:
alias eth0 forcedeth
alias snd-card-0 snd-intel8x0
options snd-card-0 index=0
install snd-intel8x0 /sbin/modprobe --ignore-install snd-intel8x0 && /usr/sbin/a
lsactl restore >/dev/null 2>&1 || :
remove snd-intel8x0 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; }; /sbin/modprobe -r --ignore-remove snd-intel8x0
#
alias usb-controller ehci-hcd
alias usb-controller1 ohci-hcd
#
# nvidia kernel module
alias char-major-195 nvidia-1_0-7174
alias nvidia nvidia-1_0-7174
#
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
alias tuner tuner-ivtv
alias tda9887 tda9887-ivtv
alias msp3400 msp3400-ivtv
dmesg output:
<snip>
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED]
cx25840: no version for "struct_module" found: kernel tainted.
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.12-1.1378_FC3 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tda9885/6/7: chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
input: AT Translated Set 2 keyboard on isa0060/serio0
cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (13353 bytes)
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = D592, serial# = 8221024
tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
tuner 0-0060: chip found @ 0xc0 (ivtv i2c driver #0)
ivtv0: This is the first unit of a PVR500
logips2pp: Detected unknown logitech mouse model 32
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 0-0060: type set to 57 (Philips FQ1236A MK4)
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNK3] -> GSI 3 (level, low) -> IRQ 3
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
tda9885/6/7: chip found @ 0x86
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (13353 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = D592, serial# = 8221024
tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 1-0061: type set to 57 (Philips FQ1236A MK4)
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv: ==================== END INIT IVTV ====================
ivtv0-osd: Specified card (id 0) is either not present or does not support TV out
<snip>
On 10/11/05, Timothy McFadden <[EMAIL PROTECTED]> wrote:
That step was specific to using a PVR-350 with TV Out ( under the
heading "Running X on the PVR-350's TV-Out" ).
-Tim
On 10/10/05, Larry K <[EMAIL PROTECTED] > wrote:
> Tim,
>
> I don't see that anywhere in Jarod's guide. Appreciate further info.
>
>
> On 10/10/05, Timothy McFadden <[EMAIL PROTECTED] > wrote:
> >
> > Also check to see if you used Jarod's mkinit-rd patch to include the
> > ivtv drivers. You need to re-make the initial ramdisk with the new
> > drivers installed.
> >
> > -Tim
> >
> > _______________________________________________
> > ivtv-devel mailing list
> > [email protected]
> > http://ivtvdriver.org/mailman/listinfo/ivtv-devel
> >
>
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
>
>
--
Want to try Gmail? Send me an email requesting an invite.
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
_______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
