I've almost got the PVR500MCE working on my KnoppMyth R5A16 based
system. The first tuner is correctly detected and is working ok.
But I cannot seem to get the second one working, and keeps giving
messages like on ivtv loading and when trying to set a frequency on the
device (e.g. through ptune.pl):
ivtv1 warning: i2c client addr: 0x00 not found for command 0x40047401!
ivtv1 warning: i2c client addr: 0x00 not found for command 0x40307603!
ivtv1 warning: i2c client addr: 0x00 not found for command 0x4004760f!
So far I've tried using ivtv 0.3.8/0.4.0 (replaced the kernel supplied
modules) and the PVR firmware 0x02040011 and 0x02050032, but to no avail.
Anybody got any suggestions as to what to try next?
/etc/modprobe.d/ivtv:
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
ivtv dmesg section:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.11.9-chw-2 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI interrupt 0000:04:08.0[A] -> GSI 17 (level, low) -> IRQ 17
tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #0
TEA5767 detected.
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect
type set to 62 (Philips TEA5767HN FM Radio)
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23559, rev = D591, serial# = 8202218
tveeprom: tuner = Philips FQ1216AME MK4 (idx = 91, type = 56)
tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom =
0x74, v4l2 = 0x00400e17)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
ivtv0: This is the first unit of a PVR500
cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded /lib/modules/HcwMakoA.ROM firmware (12282 bytes)
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: Encoder revision: 0x02040011
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
tuner: type set to 56 (Philips PAL/SECAM multi (FQ1216AME MK4)) by ivtv
i2c driver #0
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based)
ACPI: PCI interrupt 0000:04:09.0[A] -> GSI 16 (level, low) -> IRQ 16
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23559, rev = D591, serial# = 8202218
tveeprom: tuner = Philips FQ1216AME MK4 (idx = 91, type = 56)
tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom =
0x74, v4l2 = 0x00400e17)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 1-0044: loaded /lib/modules/HcwMakoA.ROM firmware (12282 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: loading /lib/modules/ivtv-fw-enc.bin
ivtv1: Encoder revision: 0x02040011
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv1 warning: i2c client addr: 0x00 not found for command 0x40047401!
ivtv1 warning: i2c client addr: 0x00 not found for command 0x40307603!
ivtv1 warning: i2c client addr: 0x00 not found for command 0x4004760f!
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv: ==================== END INIT IVTV ====================
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
