I'm running SUSE 10 (x86_64) kernel 2.6.13-7 (default kernel). Suse 10 comes with ivtv 0.3.7, but I decided to go with 0.4.1 as 0.3.7 didn't have any sound coming from the tuner, only line in.
So, I upgraded to 0.4.1 and everything seemed to be working fine, both composite+line in and the tuner. Then I noticed that after I had tuned into any one station, the sound from that station bled into the line in when I used the composite input. There seems to be no way to get rid of this. I tried every setting I could think of in ivtvctl, to force the audio input, but the audio input says "Line in", so that doesn't help. If I reload the kernel modules, then everything is fine until I tune into a station. Any ideas? I have 0.4.2 running at the moment. ACPI: PCI interrupt for device 0000:00:05.0 disabled ivtv0: Removed WinTV PVR 150, card #0 tveeprom: module not supported by Novell, setting U taint flag. cx25840: module not supported by Novell, setting U taint flag. tuner: module not supported by Novell, setting U taint flag. wm8775: module not supported by Novell, setting U taint flag. ivtv: module not supported by Novell, setting U taint flag. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.2 (development revision 3098) loading ivtv: Linux version: 2.6.13-15.7-smp SMP gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 185 tveeprom: ivtv version tveeprom: Hauppauge: model = 26559, rev = C260, serial# = 7627545 tveeprom: tuner = LG S001D MK3 (idx = 60, type = 38) tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] cx25840 debug 1-0044: detecting cx25840 client on address 0x88 cx25840 1-0044: ivtv driver cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) zaphfc: empty HDLC frame or bad CRC received (framelen = 5, stat = 0xff, card = 0). cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes) cx25840 debug 1-0044: decoder set input (0) cx25840 debug 1-0044: now setting Tuner input cx25840 debug 1-0044: set audio input (0) ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] ivtv0: i2c attach to card #0 ok [client=wm8775[50], addr=1b] cx25840 debug 1-0044: decoder set input (0) cx25840 debug 1-0044: now setting Tuner input tda9887: module not supported by Novell, setting U taint flag. tda9887 1-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) zaphfc: empty HDLC frame or bad CRC received (framelen = 4, stat = 0xff, card = 0). ivtv0: Encoder revision: 0x02040011 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0 cx25840 debug 1-0044: decoder set input (0) cx25840 debug 1-0044: now setting Tuner input cx25840 debug 1-0044: set audio input (0) tuner: switching to v4l2 insmod fixup: PAL => PAL-BG cx25840 debug 1-0044: disable output tuner: tv freq set to 400.00 tuner: tv 0x1b 0x6f 0x8e 0x02 cx25840 debug 1-0044: enable output ivtv0: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== cx25840 debug 1-0044: disable output cx25840 debug 1-0044: decoder set input (1) cx25840 debug 1-0044: now setting Composite input cx25840 debug 1-0044: set audio input (6) cx25840 debug 1-0044: enable output _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
