On Sat, 7 Jan 2006, Hans Verkuil wrote: > Sorry, 0.4.0 is too old for 2.6.15, upgrade to 0.4.1. It's not broken.
Really? Did you check recent postings to the ivtv-users mailinglist? I'm definitely not the only one having problems after upgrading to 0.4.1... > If you have problems, just post them on the list and I'll see if I can > find what's wrong. You may also want to try 0.4.2 svn. I've tried 0.4.1 and 0.4 SVN revisions 3099 and 3101 (freshly checked out and tested) with 2.6.15. All have identical behaviour: It seems as if no coax-cable is plugged to the tuner. Cannot tune into stations, shows always static. A fallback to a once working 2.6.14.3/ivtv-0.4.0 did not help either. The problem persists! Also tried ivtv-0.4.0/0.4.1/0.4.2-3099 with 2.6.14.3 and 2.6.14.5. I've not tested the 0.5 branch a lot after a couple of kernel panics (never had any with the stable 0.4 series). Is the following ok? # ivtvctl -I check SAA7115 input signal ioctl: Input detect failed (cannot read SAA regs) ioctl: Input detect failed (cannot read SAA regs) ioctl: VIDEO_STATUS = Bad SAA7115 reg[STATUS#1 - 0x1E] = 08 Color Standard (D0-D1): BW/No color White peak loop (D2): Not activated Gain value for act.lum. (min) (D3): Limited Gain value for act.lum. (max) (D4): Not limited WIPA-mode slow-time constant (D5): Not activated Horizontal frequency (D6): Locked Field length (D7): Non-standard SAA7115 reg[STATUS#2 - 0x1F] = 08 Ready for capture (D0): No Macrovision 7.01 (D1): No MV Colorstripe burst (D2): No MV Colorstripe burst type 3 (D3): Yes Input signal timebase (D4): Non-stable (VCR) Field frequency (D5): 50Hz H & V loops (D6): Locked Interlace (D7): Not detected Are the SAA7115 registers screwed up? ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.2 (development revision 3101) loading ivtv: Linux version: 2.6.15 K7 gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IRQ 217 saa7127 0-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] msp3400 0-0040: chip=MSP4418G-A2 +nicam +simple +simpler +radio mode=simpler msp3400 0-0040: msp34xxg daemon started ivtv0: i2c attach to card #0 ok [client=MSP4418G-A2, addr=40] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] tveeprom 0-0050: Hauppauge model 48134, rev J321, serial# 2771457 tveeprom 0-0050: tuner model is Philips FM1216 (idx 21, type 5) tveeprom 0-0050: TV standards PAL(B/G) (eeprom 0x04) tveeprom 0-0050: audio processor is MSP4418 (idx 25) tveeprom 0-0050: decoder processor is SAA7115 (idx 19) tveeprom 0-0050: has radio, has IR remote ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Decoder revision: 0x02020023 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv0: Create decoder VOUT stream ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) ivtv0: Initialized WinTV PVR 350, card #0 ivtv: ==================== END INIT IVTV ==================== Do you need anything else? Regards, Walter _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
