Again, using 2.6.18 kernel, so had to make the patch I previously mentioned.
Compiling went just fine. Got these errors in the dmesg: cx18: Start initialization, version 0.1.0 cx18-0: Initializing card #0 cx18-0: Autodetected Hauppauge card cx18-0: cx23418 revision 01010000 (B) tuner' 1-0010: chip found @ 0x20 (cx18 i2c driver #0-1) tuner' 1-0042: chip found @ 0x84 (cx18 i2c driver #0-1) tuner' 1-0043: chip found @ 0x86 (cx18 i2c driver #0-1) tuner' 1-004a: chip found @ 0x94 (cx18 i2c driver #0-1) tuner' 1-004b: chip found @ 0x96 (cx18 i2c driver #0-1) tuner' 1-0060: chip found @ 0xc0 (cx18 i2c driver #0-1) tuner' 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) tuner' 1-0062: chip found @ 0xc4 (cx18 i2c driver #0-1) tuner' 1-0063: chip found @ 0xc6 (cx18 i2c driver #0-1) tuner' 1-0064: chip found @ 0xc8 (cx18 i2c driver #0-1) tuner' 1-0065: chip found @ 0xca (cx18 i2c driver #0-1) tuner' 1-0066: chip found @ 0xcc (cx18 i2c driver #0-1) tuner' 1-0067: chip found @ 0xce (cx18 i2c driver #0-1) tuner' 1-0068: chip found @ 0xd0 (cx18 i2c driver #0-1) tuner' 1-0069: chip found @ 0xd2 (cx18 i2c driver #0-1) tuner' 1-006a: chip found @ 0xd4 (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client tuner' 1-006b: chip found @ 0xd6 (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client tuner' 1-006c: chip found @ 0xd8 (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client tuner' 1-006d: chip found @ 0xda (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client tuner' 1-006e: chip found @ 0xdc (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client tuner' 1-006f: chip found @ 0xde (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client cx18-0: Invalid EEPROM cs5345 1-004c: chip found @ 0x98 (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client cx18-0: Disabled encoder IDX device cx18-0: Registered device video0 for encoder MPEG (2 MB) cx18-0: Registered device video16 for TS (1 MB) cx18-0: Registered device video32 for encoder YUV (2 MB) cx18-0: Registered device vbi0 for encoder VBI (1 MB) cx18-0: Registered device video24 for encoder PCM audio (1 MB) cx18-0: Registered device radio0 for encoder radio cx18-0: Initialized card #0: Hauppauge HVR-1600 cx18: End initialization cx25840' 1-0044: cx25 0-21 found @ 0x88 (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client wm8775' 1-001b: chip found @ 0x36 (cx18 i2c driver #0-1) cx18-0: Insufficient room for new I2C client cx18-0: Insufficient room for new I2C client ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-1/1-001a/ir0 [cx18 i2c driver #0-1] cx18-0: Mismatch at offset 10 cx18-0: Retry loading firmware cx18-0: Mismatch at offset 10 cx18-0: Failed to initialize on minor 0 cx18-0: Failed to initialize on minor 0 I had a PVR-150 installed, and playback is crackly and stuttered. Unable to do a "cat /dev/video0 > test.mpg" -- I get a "cat: /dev/video0: No such device or address" error. Gonna roll back to working drivers for now. Let me know if I can provide more information. - Anthony
_______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
