Andy, My apologies, it would be more useful to put the full dmesg output, and in fact you can see as soon as eth1 comes up that the errors start, so its definitely a conflict with eth1, but I'm unsure of my options to resolve it. I've tried disabling anyting on the PCI bus that I don't need in the BIOS but I can't seem to get the system to reallocate the IRQs.
Linux video capture interface: v2.00 cx18: Start initialization, version 1.0.4 cx18-0: Initializing card #0 cx18-0: Autodetected Hauppauge card cx18 0000:00:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 cx18-0: Unreasonably low latency timer, setting to 64 (was 32) cx18-0: cx23418 revision 01010000 (B) input: PC Speaker as /class/input/input5 tveeprom 0-0050: Hauppauge model 74541, rev C6B6, serial# 5117034 tveeprom 0-0050: MAC address is 00-0D-FE-4E-14-6A tveeprom 0-0050: tuner model is Philips FM1236 MK5 (idx 116, type 43) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX23418 (idx 38) tveeprom 0-0050: decoder processor is CX23418 (idx 31) tveeprom 0-0050: has radio cx18-0: Autodetected Hauppauge HVR-1600 cx18-0: Raw VBI supported; Sliced VBI is not yet supported tuner 1-0043: chip found @ 0x86 (cx18 i2c driver #0-1) tda9887 1-0043: creating new instance tda9887 1-0043: tda988[5/6/7] found tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0) tuner-simple 1-0061: creating new instance tuner-simple 1-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) cx18-0: Registered device video0 for encoder MPEG (64 x 32 kB) DVB: registering new adapter (cx18) MXL5005S: Attached at address 0x63 DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... cx18-0: DVB Frontend registered cx18-0: Registered DVB adapter0 for TS (32 x 32 kB) cx18-0: Registered device video32 for encoder YUV (16 x 128 kB) cx18-0: Registered device vbi0 for encoder VBI (60 x 17328 bytes) cx18-0: Registered device video24 for encoder PCM audio (256 x 4 kB) cx18-0: Registered device radio0 for encoder radio cx18-0: Initialized card #0: Hauppauge HVR-1600 cx18-1: Initializing card #1 cx18-1: Autodetected Hauppauge card cx18 0000:00:0d.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 cx18-1: Unreasonably low latency timer, setting to 64 (was 32) cx18-1: cx23418 revision 01010000 (B) tveeprom 2-0050: Hauppauge model 74541, rev C6B6, serial# 5117196 tveeprom 2-0050: MAC address is 00-0D-FE-4E-15-0C tveeprom 2-0050: tuner model is Philips FM1236 MK5 (idx 116, type 43) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is CX23418 (idx 38) tveeprom 2-0050: decoder processor is CX23418 (idx 31) tveeprom 2-0050: has radio cx18-1: Autodetected Hauppauge HVR-1600 cx18-1: Raw VBI supported; Sliced VBI is not yet supported tuner 3-0043: chip found @ 0x86 (cx18 i2c driver #1-1) tda9887 3-0043: creating new instance tda9887 3-0043: tda988[5/6/7] found tuner 3-0061: chip found @ 0xc2 (cx18 i2c driver #1-1) cs5345 2-004c: chip found @ 0x98 (cx18 i2c driver #1-0) tuner-simple 3-0061: creating new instance tuner-simple 3-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) cx18-1: Registered device video1 for encoder MPEG (64 x 32 kB) DVB: registering new adapter (cx18) MXL5005S: Attached at address 0x63 DVB: registering adapter 1 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... cx18-1: DVB Frontend registered cx18-1: Registered DVB adapter1 for TS (32 x 32 kB) cx18-1: Registered device video33 for encoder YUV (16 x 128 kB) cx18-1: Registered device vbi1 for encoder VBI (60 x 17328 bytes) cx18-1: Registered device video25 for encoder PCM audio (256 x 4 kB) cx18-1: Registered device radio1 for encoder radio cx18-1: Initialized card #1: Hauppauge HVR-1600 cx18: End initialization warning: `ntpd' uses 32-bit capabilities (legacy support in use) firmware: requesting v4l-cx23418-cpu.fw cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes) firmware: requesting v4l-cx23418-apu.fw firmware: requesting v4l-cx23418-cpu.fw cx18-1: loaded v4l-cx23418-cpu.fw firmware (158332 bytes) firmware: requesting v4l-cx23418-apu.fw cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) cx18-1: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) cx18-0: FW version: 0.0.74.0 (Release 2007/03/12) firmware: requesting v4l-cx23418-cpu.fw firmware: requesting v4l-cx23418-apu.fw cx18-1: Retry loading firmware firmware: requesting v4l-cx23418-cpu.fw cx18-1: loaded v4l-cx23418-cpu.fw firmware (158332 bytes) firmware: requesting v4l-cx23418-apu.fw cx18-1: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) firmware: requesting v4l-cx23418-dig.fw cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes) cx18-1: Failed to initialize on minor 5 cx18-1: FW version: 0.0.74.0 (Release 2007/03/12) r8169: eth1: link up cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 cx18-1: Failed to initialize on minor 5 usb 2-1.4: USB disconnect, address 4
_______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
