Andy,
I tried the patches for the ACER 500 that you posted.
Purely FYI There was just one small problem with the compile in that my
version of cx18-drivers.h was missing the LEADTEK_DVR1300H entry
which I added as below:
#define CX18_CARD_LEADTEK_PVR2100 6 /* Leadtek WinFast
PVR2100/DVR3100 H */
#define CX18_CARD_LEADTEK_DVR3100H 7 /* Leadtek WinFast
PVR2100/DVR3100 H */
#define CX18_CARD_LAST 7
I probably have an old version. Thereafter it compiled and installed,
but I no longer get any /dev/video* (which I did get previously)
nor /dev/dvb/* (which I did NOT get previously). I've posted
the relevant section from dmesg below. This was following
adding patch .c files to directory
sudo make
sudo make install
"reboot"
I've not seen the "bad EEPROM" message before.
Please also find below lspci output, in case it helps.
Please note that I currently only have one card installed, the second
one is still on the bench in case you need any more hardware data, I
don't want to risk damaging it with too much unnecessary soldering
and removals.
dmesg
[ 11.942443] cx18: Start initialization, version 1.2.0
[ 11.942502] cx18-0: Initializing card 0
[ 11.942505] cx18-0: Autodetected Yuan MPC718 MiniPCI DVB-T/Analog
card
[ 11.943341] cx18 0000:02:00.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 11.943352] cx18-0: Unreasonably low latency timer, setting to 64
(was 2)
[ 11.946434] cx18-0: cx23418 revision 01010000 (B)
[ 11.949211] phy0: Selected rate control algorithm 'pid'
[ 12.078412] Broadcom 43xx driver loaded [ Features: PLR, Firmware-ID:
FW13 ]
[ 12.102583] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 12.102639] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 12.125858] tveeprom 0-0050: Encountered bad packet header [00].
Corrupt or not a Hauppauge eeprom.
[ 12.125863] cx18-0: Invalid EEPROM
[ 12.125867] cx18-0: Experimenters needed for device to work well.
[ 12.125869] To help, mail the ivtv-devel list (www.ivtvdriver.org).
[ 12.258180] tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
[ 12.306617] xc2028 1-0061: creating new instance
[ 12.306620] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
[ 12.306986] cx18-0: Registered device video0 for encoder MPEG (64 x
32 kB)
[ 12.306990] DVB: registering new adapter (cx18)
[ 12.307305] cx18-0: frontend initialization failed
[ 12.307508] cx18-0: DVB failed to register
[ 12.307570] cx18-0: Registered device video32 for encoder YUV (16 x
128 kB)
[ 12.307628] cx18-0: Registered device vbi0 for encoder VBI (20 x
51984 bytes)
[ 12.307688] cx18-0: Registered device video24 for encoder PCM audio
(256 x 4 kB)
[ 12.307763] cx18-0: Registered device radio0 for encoder radio
[ 12.308241] cx18-0: Error -1 registering devices
[ 12.308320] xc2028 1-0061: destroying instance
[ 12.308892] cx18-0: Error -1 on initialization
[ 12.308902] cx18: probe of 0000:02:00.0 failed with error -1
[ 12.308952] cx18: End initialization
st...@cinema:~$ ls /dev/dvb*
ls: cannot access /dev/dvb*: No such file or directory
st...@cinema:~$ ls /dev/vid*
ls: cannot access /dev/vid*: No such file or directory
ALSO FROM LSPCI
02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23418
Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio
Decoder
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
