Hi again,
The trick with doing a "mv tveeprom-ivtv.ko tveeprom.ko" actually helped me to detect the tuner.
But after a while before i managed to tune in any channel ivtv froze. (Se the dmesg output below.)
Is late here so ill hit the sack now. Does anyone have any hints on ehat to tune next?
/Chris
Linux video capture interface: v1.00
ivtv: no version for "struct_module" found: kernel tainted.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3b) loading
ivtv: Linux version: 2.6.10-1.9_FC2 686 REGPARM 4KSTACKS gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: VIA PCI device: 0x0258 vendor: 0x1106
tveeprom: Hauppauge: model = 48139, rev = K257, serial# = 2912318
tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38)
tveeprom: tuner fmt = PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
tveeprom: audio_processor = CS5331 (type = 9)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 38, Tuner formats 0x00400e17, Radio: yes, Model 0x00ad2557, Revision 0x00000001
ivtv: PAL tuner detected
ivtv: SECAM tuner detected
ivtv: Radio detected
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x48, (1F) 0xc0
saa7127: video encoder driver version V 0.3 loaded
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[0],ok]
msp34xx: init: chip=MSP3418W-B3 +nicam +simple +simpler +radio mode=simple
ivtv: i2c attach [client=MSP3418W-B3,ok]
msp3410: daemon started
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 9 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 5 minor 16
ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total
ivtv: Registered v4l2 device, streamtype 6 minor 228
ivtv: Create stream 7
ivtv: Registered v4l2 device, streamtype 7 minor 232
ivtv: Create DMA stream 8
ivtv: Registered v4l2 device, streamtype 8 minor 48
ivtv: Setting Tuner 38
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to PAL.
saa7115: decoder set norm PAL
saa7115: set audio: 0x01
saa7127: Setting Encoder Video Standard
saa7127: Set PAL Video Mode
saa7127: Selecting PAL video Standard
ivtv: ivtv_enc_thread: pid = 3704, itv = 0xe0b3a1a0
ivtv: ivtv_dec_thread: pid = 3705, itv = 0xe0b3a1a0
ivtv: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
saa7115: decoder disable output
saa7115: decoder enable output
lirc_dev: IR Remote Control driver registered, at major 61
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
saa7115: decoder disable output
saa7115: decoder enable output
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000d2 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000d2 with result 0xfffffff0
saa7115: decoder disable output
saa7115: decoder enable output
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000d2 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x00000082 with result 0xfffffff0
ivtv: ENC: Failed stopping capture -16
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000d5 with result 0xfffffff0
ivtv: ENC: Failed stopping event notification -16
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000c6 with result 0xfffffff0
ivtv: No Free Mailbox for cmd 0x000000d9 after 100 tries!
ivtv: Mailbox[0] 0x000000d3 flags 0x00000003
ivtv: Mailbox[1] 0x000000c9 flags 0x00000003
ivtv: Mailbox[2] 0x000000d6 flags 0x00000003
ivtv: Firmware UNRESPONSIVE when trying cmd 0x000000d9!!!
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
ivtv: 1000 ms time out waiting for firmware
ivtv: Failed api call 0x000000b7 with result 0xfffffff0
On Fri, 21 Jan 2005, Christopher Arnold wrote:
On Thu, 20 Jan 2005, Alan Gonzalez wrote:
Can you list out all modules you have loaded(lsmod)
Shure they are included below. With other relevant information.
I looked into this and even tried doing a modload in /etc/rc still the same symptom.Also read this thread about ordering of modules.
http://gossamer-threads.com/lists/ivtv/devel/15461?search_string=0x50
This seems to say it's ordering of your modules, possibly bttv related.
This seems to very wierd. If you or anyone else would like to look into this i could provide an account on the machine for you. Just tell me.
/Chris
# uname -a
Linux tv.arnold.se 2.6.10-1.9_FC2 #1 Thu Jan 13 17:54:57 EST 2005 i686 i686 i386 GNU/Linux
# modinfo ivtv
parm: tuner:Tuner type selection, see tuner.h for values
parm: tda9887:Enable or disable tda9887 module, 0 = normal, 1+ = pinnacle_id
parm: radio:Enable or disable the radio. Use only if autodetection fails. 0 = disable, 1 = enable
parm: autoload:automatically load i2c modules like tuner.o, default is 1 (yes)
parm: cardtype:Only use this option if your card is not detected properly.
Specify card type:
1 = WinTV PVR 250
2 = WinTV PVR 350
3 = AVerMedia M179
4 = YUAN MPG600/Kuroutoshikou iTVC16-STVLP
5 = YUAN MPG160/Kuroutoshikou iTVC15-STVLP
Default: Autodetect
parm: ivtv_debug:Debug level (bitmask). Default: errors only (ivtv_debug = 255 gives full debugging)
parm: ivtv_std:Specify video standard: 1 = NTSC, 2 = PAL, 3 = SECAM, Default: Autodetect
parm: ivtv_first_minor:Set minor assigned to first card
author: Kevin Thayer
description: iTVC15_16 driver
license: GPL
version: 0.2.0-62_rc3d.rhfc2.at
vermagic: 2.6.10-1.9_FC2 686 REGPARM 4KSTACKS gcc-3.3
depends:
srcversion: FC933F94F3589AEAB9F124A
# lsmod
Module Size Used by
nls_utf8 2241 1
udf 75461 0
snd_pcm_oss 48117 0
snd_mixer_oss 17089 1 snd_pcm_oss
snd_via82xx 27489 0
snd_ac97_codec 67361 1 snd_via82xx
snd_pcm 93001 3 snd_pcm_oss,snd_via82xx,snd_ac97_codec
snd_timer 28741 1 snd_pcm
snd_page_alloc 9669 2 snd_via82xx,snd_pcm
gameport 5057 1 snd_via82xx
snd_mpu401_uart 8897 1 snd_via82xx
snd_rawmidi 25569 1 snd_mpu401_uart
snd_seq_device 8653 1 snd_rawmidi
snd 53413 9 snd_pcm_oss,snd_mixer_oss,snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 10017 1 snd
msp3400 23401 0
saa7127 10396 0
saa7115 10648 0
tuner 20268 0
tveeprom 11032 0
ivtv 796388 0
i2c_algo_bit 8521 1 ivtv
i2c_core 21057 6 msp3400,saa7127,saa7115,tuner,tveeprom,i2c_algo_bit
videodev 9409 1 ivtv
parport_pc 26501 1
lp 12077 0
parport 37257 2 parport_pc,lp
autofs4 23365 0
sunrpc 155813 1
via_rhine 23497 0
mii 4801 1 via_rhine
ipt_REJECT 6593 1
ipt_state 2113 7
ip_conntrack 41205 1 ipt_state
iptable_filter 3777 1
ip_tables 16577 3 ipt_REJECT,ipt_state,iptable_filter
floppy 57585 0
sg 34145 0
microcode 6497 0
xfs 518065 1
uhci_hcd 31577 0
ehci_hcd 34761 0
video 15813 0
button 6609 0
battery 9413 0
ac 4933 0
md5 4161 1
ipv6 235649 10
ext3 120905 2
jbd 69209 1 ext3
dm_mod 56021 2
sata_via 7237 0
libata 41541 1 sata_via
sd_mod 16577 0
scsi_mod 122177 3 sg,libata,sd_mod
# more /etc/modprobe.conf
alias eth0 via-rhine
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-61 lirc_i2c
alias scsi_hostadapter sata_via
alias snd-card-0 snd-via82xx
install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx && /usr/sbin/alsactl restore >/dev/null 2>&1 || :
remove snd-via82xx { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; }; /sbin/modprobe -r --ignore-remove snd-via82xx
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
# ivtv modules setup
#options ivtv ivtv_debug=1 tuner=50 ivtv_std=2 cardtype=1
#options ivtv ivtv_debug=1 tuner=48 ivtv_std=2 cardtype=2
#install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c
install eeprom /sbin/modprobe tveeprom; /sbin/modprobe --ignore-install eeprom
from dmesg: ivtv: no version for "struct_module" found: kernel tainted. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.2.0 (rc3b) loading ivtv: Linux version: 2.6.10-1.9_FC2 686 REGPARM 4KSTACKS gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 350 card ivtv: Found an iTVC15 based chip ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: VIA PCI device: 0x0258 vendor: 0x1106 ivtv: i2c client addr: 0x50 not found! ivtv: Error -19 reading Hauppauge eeprom. ivtv: Possible causes: the tveeprom module was not loaded, or ivtv: the eeprom kernel module was loaded before the tveeprom module. tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[0],ok] saa7115: status: (1E) 0x40, (1F) 0xc0 saa7127: video encoder driver version V 0.3 loaded saa7127: Selecting NTSC video Standard saa7127: Selecting S-Video+Composite saa7127: Turn WSS off saa7127: Widescreen Mode 4:3 Full Format saa7127: Selecting Normal Encoder Input saa7127: Enable Video Output ivtv: i2c attach [client=saa7127[0],ok] msp34xx: init: chip=MSP3418W-B3 +nicam +simple +simpler +radio mode=simple ivtv: i2c attach [client=MSP3418W-B3,ok] msp3410: daemon started ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware is buggy, use version 0x02040011 ivtv: Decoder revision: 0x02020023 ivtv: Configuring WinTV PVR 350 card with 9 streams ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 1 ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create stream 4 ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total ivtv: Registered v4l2 device, streamtype 5 minor 16 ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total ivtv: Registered v4l2 device, streamtype 6 minor 228 ivtv: Create stream 7 ivtv: Registered v4l2 device, streamtype 7 minor 232 ivtv: Create DMA stream 8 ivtv: Registered v4l2 device, streamtype 8 minor 48 ivtv: Could not detect tuner standard, defaulting to NTSC. tuner: tuner type not set ivtv: Setting audio matrix to input 3, output 1 ivtv: Switching standard to NTSC. tuner: tuner type not set saa7115: decoder set norm NTSC saa7115: set audio: 0x01 saa7127: Setting Encoder Video Standard saa7127: Set NTSC Video Mode saa7127: Selecting NTSC video Standard ivtv: ivtv_enc_thread: pid = 3676, itv = 0xe0b3a1a0 ivtv: ivtv_dec_thread: pid = 3677, itv = 0xe0b3a1a0 ivtv: Initialized WinTV PVR 350, card #0 ivtv: ==================== END INIT IVTV ====================
------------------------------------------------------- This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting Tool for open source databases. Create drag-&-drop reports. Save time by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc. Download a FREE copy at http://www.intelliview.com/go/osdn_nl _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
------------------------------------------------------- This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting Tool for open source databases. Create drag-&-drop reports. Save time by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc. Download a FREE copy at http://www.intelliview.com/go/osdn_nl _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
